background image

 

Triton

 

 

Installation and Operation Instructions - Parts List 

VS80-130

 

 

 

 

28 

Terms and Conditions 

 

1.

 

This warranty is VOID if: 
a.

 

The appliance is not installed and serviced by a licensed and trained Heating Technician. 

b.

 

The installation is not in accordance with this manufacturer’s manuals, local codes, and regulations. 

c.

 

The heating system does not provide and ensure required flow through the heat exchanger when the 
burner is on. 

d.

 

Deformation occurs due to freezing; improper storage or handling; improper firing or firing without water. 

2.

 

Any repairs or replacements made without authorization by or notification to the manufacturer. 

3.

 

This warranty does not cover the labour and shipping costs associated with installing a repaired or replaced 
boiler. 

4.

 

Installations determined to have any leaks in the entire heating system causing make up water to enter the 
system (e.g. Solder leaks, coil gasket leaks, frequent system drainage). 

5.

 

Decision of warranty repairs or replacements to appliances will be at the discretion of the manufacturer or 
authorized service representative. 

6.

 

This warranty is to the original owner only.

      

 

 
What To Do In The Case of A Warranty Service Problem 

1.  Contact your installing contractor or service provider. Do not call NTI. 
2.  If your contractor or service representative requires further help, they will contact us directly. 
3.  If you cannot contact your contractor or service representative, contact us at 1-506-657-6000 to the attention 

of the Service Department.  

 

NOTE:

 

NTI cannot provide technical assistance to homeowners unless they are a licensed and trained 

Heating Technician.

 

4.

 

We  as  the  appliance  manufacturer  will  replace  or  credit  the  parts  under  warranty;  credits  are  issued  to  the 
authorized  wholesaler  at  their  cost,  so  do  not  purchase  replacement  parts  from  suppliers  with  hopes  of 
receiving  100%  credit;  it  is  recommended  to  receive  all  your  warranty  parts  from  your  authorized  service 
representative or us directly, at no charge (if under the warranty coverage). 

5.

 

We care about the quality of service you receive, so please let us know if you have complaints concerning 
your authorized service representative. 

 
 
 

For Service Contact: 

 

Name:   ____________________________________ 

 
 
 

 

 
 

 

 

Warranty Registration Form 

Triton Oil Boiler

 

Owner’s Name 

 

Address 

 

City 

 

Province / State 

 

Boiler Model 

 

Serial Number 

 

Installer’s Name 

 

Date of Installation 

 

Complete this form, photocopy, and return to:  

NTI Boilers Inc.   30 Stonegate Dr.    Saint John, N.B.    E2H 0A4    Canada 

 

 

Содержание Triton VS100





























Отзывы: