background image

9

This section describes the allowable tolerances for installation in order to maximize the 

performance of NSK linear guides.
We recommend that the mounting errors e

1

 or e

2

 do not exceed the values shown in the table 

below. Consult “Precision Machine Components” catalog for linear guides series not shown.

If the error readings are equal to or less than the above values, you have correctly assembled 

the parts. For maximum accuracy, keep the readings below what is shown in the table. 
If your readings are greater than these values, it is necessary to remove the parts and 

start over. Please contact your local NSK office with any questions or for assistance. Visit 

www.nskamericas.com

 for contact information.

Recommended allowable installation error of the NS Series (Maximum) 

Item

Model No.

15

20

25

30

35

Clearance

Z0, ZT

Permissible values of parallelism 
in two rails: e

1

20

22

30

35

40

Permissible values of parallelism 
(height) in two rails: e

2

375

m

m/500mm

Preload

Z1, ZZ

Permissible values of parallelism 
in two rails: e

1

15

17

20

25

30

Permissible values of parallelism 
(height) in two rails: e

2

330

m

m/500mm

Recommended  allowable  installation  error  of  the  NH  Series  (Maximum)                                

Item

Model No.

20

25

30

35

45

55

65

Clearance

Z0, ZT

Permissible values of parallelism 
in two rails: e

1

30

40

45

55

65

80

110

Permissible values of parallelism 
(height) in two rails: e

2

375

m

m/500mm

Preload

Z1, ZZ

Permissible values of parallelism 
in two rails: e

1

20

25

30

35

45

55

70

Permissible values of parallelism 
(height) in two rails: e

2

330

m

m/500mm

Содержание NH 20













Отзывы: