background image

Blackout pad

Each tap of the Blackout pad will cause functions to deactivate or ‘‘clear’’  in the following
order.

1. Latches.

2. Patterns.

It may require up to two taps of the Blackout pad to entirely clear all functions.

The Blackout Led will light when and all Latch pads have been deactivated.

Lights affected by each function will fade out at the set fade rate.

Touching and holding down the Blackout pad will bypass the set fade rate and cause the
selected functions to fade out instantly.

Master Level
Pads

The Master control provides proportional level control over all console functions to stage
with the exception of the Bump pads. For example:

Whenever the Master is at minimum all stage outputs will be at zero except for any resulting
from a Bump pad. 

If the Master is at 50% all stage outputs will be at only 50% of their current console settings
except for any resulting from a Bump pad. 

If the Master is at full all stage outputs will follow the console settings.

The Master level is indicated by the display in a number from 0 - 100 percent (100 is
indicated as FL) whenever the LED above the pads is lit. 

Program pad

The Program pad is used to program chase patterns or static scenes into the pattern memory
or to program audio intensity effects.  For programming details see the next section on
PROGRAMMING.

TLC 16

Operation Guide

Software Revision 1.00 version A and above

Blackout pad

NSI CORPORATION

Features and Specifications may change without notice 

7

Содержание TLC16





















Отзывы: