Novoferm tormatic NovoCon T75 DES, Монтаж и эксплуатация

Страница: 19 / 77

Fault diagnosis
Fault Condition Diagnosis/Remedy
__________________________________________________________________________________________________________________
E05 Gate neither opens nor closes Safety circuit at J3 is interrupted.
Check the slack rope switch; wicket door not closed.
__________________________________________________________________________________________________________________
E06 cables. In the case of Gate reverses/does not close Edge safety device has tripped; check the edge safety device and is
[35] pressed. an AK edge safety device keep the programming button in menu
_________________________________________________________________________________________________________
E07 Gate reverses/does not close The light barrier has tripped.
__________________________________________________________________________________________________________________
E08 Gate neither opens nor closes The thermo-contact for the drive has tripped; let the drive cool down.
Emergency drive release; unlock the drive again.
__________________________________________________________________________________________________________________
E09 [30] / [31]. Gate neither opens nor closes No end position taught-in; tech-in the gate end positions in menus
__________________________________________________________________________________________________________________
E10 the gate completely, Teach-in of the light barrier position Position of the light barrier in the frame not taught in. Open and close
adjust the light barrier.
__________________________________________________________________________________________________________________
E51 check it. Gate does not open Permanent start of the cover button OPEN, button might be jammed,
__________________________________________________________________________________________________________________
E52 might not have Gate neither opens nor closes Cover button STOP has been pressed. Button might be jammed. Cable
been plugged in.
__________________________________________________________________________________________________________________
E53 . Gate does not close Permanent start of the cover button CLOSE, button might be jammed
__________________________________________________________________________________________________________________
E54 . Gate does not open Permanent start J1.3 > button OPEN, button might be jammed, check it
__________________________________________________________________________________________________________________
E55 Gate neither opens nor closes External STOP button J1.2 has been pressed or bridge is missing. Check
connecting cable to the external command transmitter. __________________________________________________________________________________________________________________
E56 Gate does not close Permanent start J1.4 > button CLOSE, button might be jammed, check it
__________________________________________________________________________________________________________________
E5E Gate only closes in the dead-man mode Service cycle has expired; have the system serviced.
Subject to modifications
Fault Condition Diagnosis/Remedy
__________________________________________________________________________________________________________________
F2 . No response Fault during the self-test; switch control off/on
__________________________________________________________________________________________________________________
F3 . No response Fault during the self-test; switch control off/on
__________________________________________________________________________________________________________________
F4 . No response Fault during the self-test; switch control off/on
__________________________________________________________________________________________________________________
F5 . No response Fault during the self-test; switch control off/on
__________________________________________________________________________________________________________________
F6 . No response Fault during the self-test; switch control off/on
__________________________________________________________________________________________________________________
F10 . Gate stops after the start command Fault in the control electronics; switch control off/on
__________________________________________________________________________________________________________________
F19 Gate only closes in the dead-man mode Test of the DW edge safety device failed; check the edge safety device.
__________________________________________________________________________________________________________________
F20 . Gate only closes in the dead-man mode Test of the light barrier failed; check the light barrier
__________________________________________________________________________________________________________________
F21 Brief interruption of operation Runtime limitation of the gate; let the drive cool down for approx. 20 min
__________________________________________________________________________________________________________________
F24 . No response to the start command No connection with the DES; check both power supply cable and DES
__________________________________________________________________________________________________________________
F27 . in menus 33 &34 Gate does not reach end position; gate Springs overstressed. Check the door balance. Adjust the end positions
neither opens nor closes Drive is blocked. Check the gate's mechanical system,the mains and motor phases.
__________________________________________________________________________________________________________________
F28 No response to the start command Fault in the power supply; check the connection with the mains.
Check whether the 24-V consumers are short-circuited.
__________________________________________________________________________________________________________________
F29 adjust them. Motor rotates in the wrong direction Mains phases have been transposed: correct the mains phases or re
Gate stops after the start command Gate drive is too fast, the overrun of the drive is too high.
Gate stops after reversing
__________________________________________________________________________________________________________________
F30 Gate only closes in the dead-man mode Return of the pulse into the dead-man mode. Edge safety device or light barrier has tripped.
Opening force limitation has been activated. The motor's power-on time has been exceeded.
__________________________________________________________________________________________________________________
F33 Gate stops during opening The opening force limitation has tripped. Gate can only be closed in the dead-man mode.
Rectify the gates sluggishness or blockage. Check the springs. Eliminate the cause of
exceeding the force limitation and open and close the gate thereafter.
__________________________________________________________________________________________________________________
F34 Gate neither opens nor closes The motor's power-on time (menu 49) has been exceeded. Wait a while and let the motor cool down.