background image

INTRODUCTION

Main Features

• 

2

Thank you for purchasing the Novation SpeedIO USB interface. The SpeedIO is a state of the art product -
it combines a 16 channel MIDI input and output interface along with a high quality audio interface. 

When used with a computer running a MIDI / Audio sequencer package it will provide a superb, compact
recording setup with only a single USB cable required to connect both MIDI and Audio signals to the com-
puter.

Main Features

Two Novation high precision, low noise high bandwidth audio pre-amplifiers with switchable 
phantom power and over 70 dB headroom deliver a warm, clear signal typical of Novations 
commitment to sonic excellence.

*

Integrated USB low latency Audio and MIDI - Requires just a single USB connection a computer 
(no PSU needed)

*

Separate headphone and line output level controls allowing fast recording / monitoring 
turnaround.

*

Continuously variable Monitor control allows for direct hardware zero latency monitoring or low 
latency software monitoring via the audio application.

*

44.1 / 48 Khz 16 / 24 bit simultaneous 2 channel Audio input and output operation with concur-
rent MIDI transmission and reception. 

*

Independent Gain controls with LED signal level and overload display. Each channel has 20dB 
boost switches.

*

Driver software included to run on Windows XP or Mac OSX Operating systems.

SpeedIO v10.qxd  23/01/04  12:05  Page 2

Содержание SpeedIO














Отзывы: