manualshive.com logo in svg

Novatel Expedite, Справочное руководство

Поделиться
Скачать
Novatel Expedite Скачать руководство пользователя страница 50

N O V A T E L   W I R E L E S S   T E C H N O L O G I E S   L T D .                  

5 0

A T   C o m m a n d   S p e c i f i c a t i o n - E x p e d i t e   a n d   M e r l i n

W i r e l e s s   I P   M o d e m s

UDP Half Open Mode

Description:

Once the modem is configured to operate in the half-open mode, it can accept AT commands from the
keyboard, it can also receive UDP packets through the RF channels for the duration specified by the user
without performing and ATD command.

The modem can accept UDP packets from any destination.  But once it receives a packet, it locks onto
that destination and automatically goes into the regular UDP mode.   It stays in that mode until either the
DTR is dropped, the escape sequence is sent or the Half-Open timer expires.  The timer restarts every
time a packet is received or sent.  For example, if the timer is set to 30, the Monitor will stay in the UDP
mode until 30 seconds after the last UDP packet is received or sent.  Once the modem exits active UDP,
it returns to the Half-Open mode.

If the destination address is set to a nonzero value, everything will work the same as the above except that
it will only accept UDP packets from that specific destination and ignore the rest.

Format:

 ATS82=0

regular mode

 ATS82=1

not used (reserved)

 ATS82=2

Half-Open mode enabled

Query:

ATS82?

Command:

ATS82=<mode>

Where <mode>

0 = Regular mode
1 = Not used (reserved)
2 =  Half-Open mode

Validity:

This command can only be issued in command mode.

Other Considerations:

Register S83 is used as the half-open timer.  Setting this register to a non-zero value permits the
automatic UDP stack to remain active for that amount of time (measured in seconds).

ATS83?

Query UDP Open Timeout

ATS83=60

Set UDP Open Timeout

sets the timer to 60 seconds.

Related Topics:

Содержание Expedite











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды