background image

~ 4 ~ 

EM-129 

                                  

                                                                               

NOVATEK-ELECTRO

 

Status condition indication: 

• Blue (flashes) - connects to a Wi-Fi access point; 
• Blue (on) - the load is on, there is a connection to Wi-Fi; 
• Blue (flashes once every 5 seconds) - the load is off, there is a connection to Wi-Fi; 
• Red flashes) - the countdown of the re-closure time is in progress; 
• Red (on) – a failure or the device is blocked due to a failure; 
• Blue - red (flashing) - Wi-Fi connection setup mode is on; 
• Purple - the settings are reset to the factory settings, the embedded software is updated, or the Wi-Fi control button 

is pressed. 

 

1.3. Operation conditions 

 The device is intended for operation in the following conditions: 

 

Ambient temperature: from minus 30 to +50 

°С; 

 

Atmospheric pressure: from 84 to 106.7 kPa; 

 

Relative humidity (at temperature of +25 

°С): 30 … 80 %. 

 

ATTENTION! The device is not intended for operation in the following conditions: 

 

Significant vibration and shocks; 

 

High humidity; 

 

Aggressive  environment  with  content  in  the  air  of  acids,  alkalis,  etc.,  as  well  as  severe  contaminations  

          (grease, oil, dust, etc.). 

 

2. TECHNICAL SPECIFICATIONS

 

2.1 Main technical specifications 

The main technical characteristics of meter EM-129 are shown in Table 1.  
The adjustable parameters of meter EM-129 are shown in Table B1 - Appendix B. 

 

Table 1 - 

Main technical specifications   

    

Description 

Value 

Operating supply voltage, V 

220 

– 240 

Supply frequency, Hz 

50 / 60 

Voltage at which operability remains, V 

100 

– 450 

Maximum switching current at active load, A 

63 

Power of connected load, W, no more 

14 000 

Ready time at supply voltage supply, s, no more 

1.5 

Shutdown  delay  at  voltage  increase  of  more  than  420  V  and  duration  of  more  than  
2.0 ms, s, no more 

0.05 

Shutdown delay at voltage increase of more than 30 V from the setting “Upper voltage 
threshold”, s 

0.2 

Shutdown delay when voltage drops below 145 V, s 

0.25 

Range of voltage measurement, V 

100 

– 350 

Accuracy of measurement of the mains voltage, % (from the range) 

±1 

Current measurement range, A 

0.3 

– 65 

Load current accuracy measurement, % (from the range) 

±2 

Range of power measurement, W 

300 

– 30 000 

Power measurement accuracy,% (of range) 

±3 

Range of frequency  measurement, Hz 

45 

– 65 

Accuracy of frequency measurement, Hz 

±0.03 

Real-time clock accuracy 

1

, s / day 

±1 

Real-time clock reserve 

2

, day 

Up to 5 

Wi-Fi frequency, GHz 

2.412 

– 2.484 

Supported Wi-Fi Standards 

IEEE 802.11 b/g/n 

Wi-Fi Encryption Protocol 

WPA2/PSK 

Protocol for synchronizing time with an NTP server 

Yes 

Protocol for exchanging data with the "my.overvis.com" server 

Yes 

Maximum number of events (schedule) 

512 

Maximum log length, entries 

10 000 

Log Entry Type 

In a loop 

Log recording period 

3

, min 

Tightening torque of terminal block screws, N * m 

2 ±0.2 

Designation of the device 

Control and 

distribution equipment 

Rated operating mode 

Long 

Climatic modification 

NF 3.1 

Device Protection 

ІР20 

Содержание EM-129

















Отзывы: