Novatek-electro OM-310, Руководство пользователя

Страница: 22 / 29

- 22 -
ОМ-310
NOVATEK-ELECTRO
When

=1, the ОМ
-310 device after power-on works similarly as when the remote control is off (normal oper-
ation), but writing to the R_COMMAND command register is permitted.
When

=2, ОМ
-310 will energize load only after the corresponding command via RS-232/RS-485 has been
received.
The R_COMMAND value is regarded by the
ОМ
-310 operation algorithm when

=1,

=2. If

=0 and the
user sets

=1 or

=2, then 0 will be recorded to R_COMMAND.
The list of possible command register settings is shown in Table 2.7
Table 2.7
R_COMMAND command
register Address=220 Actions performed
0 De-energize load. If the load is de-energized, then before a power-on command
from the Remote Control has been received, the load will not energize. If the load is
energized, it will be de-energized.
1 Normal device operation.
If the load was de-energized by the remote control command or by pressing DOWN,
UP buttons (while

=3), or in case of a failure after which automatic restart is per-
mitted, then the load will be energized within specified automatic restart time from
the moment of de-energizing while “1” is recorded in the R_COMMAND register.
2 Early load energizing. Value “2” record will lead to load power-on until expiration of
the automatic reset time period. After load power-on, R_COMMAND =1.
If

=1, then after energizing “1” value (device normal operation) will be recorded in the command register.
If

=2, then after energizing “0” value (load de-energized until the command to energize is received) will be
recorded in the command register.
In case of an emergency load shutdown by simultaneous pressing DOWN, UP buttons, (while

=2,

=3),
the command register will be reset to 0.
2.4.6 Load energize/de-energize via remote breaker
ОМ
-310 operation in the remote control mode is defined by the

parameter.
When

=0, the load energize/cutoff by means of remote breaker is prohibited.
When

=1,
ОМ
-310 with the open terminal of the S1 remote breaker (fig.2.1) functions the same way as dur-
ing normal operation mode. When the remote breaker terminal is closed the load relay opens (when

=2 besides
the load relay, the characterizing relay will also open).
When

=2,
ОМ
-310 with the closed terminal of the S1 remote breaker (fig.2.1) functions the same way as
during normal device operation. When the remote breaker terminal is open the load relay opens (when

=2 be-
sides the load relay, the characterizing relay will also open).
When

=3 and

= 4
ОМ
-310 functions the same way as

=1 and

= 2 accordingly, but AR after the
remote motor de-energizing is forbidden.
2.4.7 Fault conditions system
In case of fault condition occurrence, the
ОМ
-310 performs following actions:
-mnemonic indicator displays error code according to Table 2.8;
-value indicator displays value of the faulty parameter (if given fault does not have numeric value, the indicator
displays “ ---- “);
-red LED FAULT lights (glows continuously if AR will not initiate, and flickers if AR is expected);
- load relay opens;
- characterizing relay closes (when

=0).
If
ОМ
-310 defines several types of faults simultaneously, the error codes and parameter values are displayed
consecutively, one after one.
If AR is permitted, the fault codes and time left till AR are displayed.
2.4.8 Faulty conditions log
When load relay in case of fault opens, the
ОМ
-310 device stores the fault code, the parameter value, and time
of occurrence.
Note. Time of fault is defined by OM internal clock. As
ОМ
-310 has no integral power source, the time when the
device was de-energized, is not accounted.
Number of synchronously stored fault codes is five. When next following faults occur, the information of this fault
is recorded over the latest fault.
To view log press RES/MEM/SEL button.