Northern 337007, Руководство пользователя

Страница: 3 / 7

If in doubt, use larger cord.
Be sure to check voltage requirements of the tool to your incoming power source.
·
Do not expose the sharpener to rain or wet conditions. Water entering the sharpener will increase the risk of electric shock.
·
Do not let your fingers touch the terminals of plug when installing to or removing from the outlet.
·
Ground fault circuit interrupters. If work area is not equipped with a permanently installed Ground Fault Circuit Interrupter outlet (GFCI),
use a plug-in GFCI between power tool or extension cord and power receptacle.
PERSONAL SAFETY
·
Stay alert, watch what you are doing and use common sense when operating the shapener. Do not use the tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal
injury.
·
Dress properly. Do not wear loose clothing, dangling objects, or jewelry. Keep your hair, clothing and gloves away from moving parts.
Loose clothes, jewelry or long hair can be caught in moving parts. Air vents often cover moving parts and should be avoided.
·
Use safety apparel and equipment. Use safety goggles or safety glasses with side shields which comply with current national standards,
or when needed, a face shield. Use as dust mask in dusty work conditions. This applies to all persons in the work area. Also use non-skid
safety shoes, hardhat, gloves, dust collection systems, and hearing protection when appropriate.
·
Avoid accidental starting. Ensure the switch is in the off position before plugging tool into power outlet. In the event of a power failure,
while a tool is being used, turn the switch off to prevent surprise starting when power is restored.
·
Do not overreach. Keep proper footing and balance at all times.
·
Remove adjusting keys or wrenches before connecting to the power supply or turning on the tool. A wrench or key that is left attached to
a rotating part of the tool may result in personal injury.
TOOL USE AND CARE
·
Do not force the sharpener. Tools do a better and safer job when used in the manner for which they are designed . Plan your work,
and use the correct tool for the job.
·
Never use a sharpener with a malfunctioning switch. Any tool that cannot be controlled with the switch is dangerous and must be
repaired by an authorized service representative before using.
·
Disconnect power from sharpener and place the switch in the locked or off position before servicing, adjusting, installing
accessories or attachments, or storing. Such preventive safety measures reduce the risk of starting the power tool accidentally.
·
Store idle sharpeners. When tools are not in use, store them in a dry, secure place out of the reach of children. Inspect tools for
good working condition prior to storage and before re-use.
·
Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool
may create a risk of injury when used on another tool.
·
Never touch the moving grinding wheel.
·
The sharpener's motor is specially rated for intermittent use 15 minutes continuous use.
·
Do not attach modules when the grinding wheel is moving .
·
Do not use the grinding wheel without a module in place .
·
Keep guards in place and in working order.
OPERATION
Sharpens all high speed steel drill bits from 7/64" (3mm) to
3/8" (50mm)
Unique "True Point" action ensures accurate finish
Precisely locates high speed steel drills for correct sharpening
angles
Re-sharpen broken drill bits
SHARPENING HSS BITS
1.Slide module, labeled High Speed Steel Drill Sharpener, on
to the Power Unit.
2.Remove the clamp holder and insert the drill bit to be sh
arpened (1a). Tighten the clamp lightly to leave the drill bit
still free to move.
3.Place the clamp containing your drill bit into the setting slot,
using the grooves in the side to lower it in correctly (1b).
4.Move the drill bit forward up so that it lies in the V-guide and
touches the metal end stop (1c).
5.Turn the drill bit until the V-guide fully drops over it (1c) all
for drill bit corners should now be touching the V-guide sides.
6.Ensure that the drill and holder are fully down in the setting
Slot. With the drill bit in this position, tighten the clamping ring (1d).
7.Lift up the V-guide and remove the clamp and drill bit.
8.Transfer the clamp and drill bit into the clamp holder on the
Power Unit modules (1e).
9.Switch the Power Unit on.
10.Move the clamp holder from side to side, securing with light finger
Pressure (1f).
11.Remove the drill bit and holder and turn over (1g). Repeat step No. 11.
12.Check that the leading edge of both flutes are equally sharp. They should meet exactly in the middle as in (1h), not (1i).
13.Switch the Power Unit off. Before removing the module, ensure the grinding wheel has stopped.
·
Before removing a module, switch power OFF, allow grinding wheel to come to a complete stop and unplug the machine.
·
·
Never sharpen more than one item at a time.
Do not jam the workpiece against the sharpening surface.
Firmly grasp the workpiece and ease it against the sharpener using light
pressure.
2 OF 5