manualshive.com logo in svg

Northern Lights M843JK, Руководство оператора

Поделиться
Скачать
Northern Lights M843JK Скачать руководство пользователя страница 17

O843K  05/03

15

Servicing

SP10.  BLEEDING THE FUEL SYSTEM

CAUTION:  Escaping diesel fuel under pressure can penetrate skin causing serious personal injury.
Before disconnecting lines be sure to relieve all pressure. Before applying pressure, be sure all connections
are tight and lines, pipes and hoses aren't damaged. Fuel escaping from a very small hole can be almost
invisible. Use a piece of cardboard or wood, rather than hands, to search for suspected leaks. If injured by
escaping fuel, see a doctor at once. Serious infection or reaction can develop if proper medical treatment
isn't administered immediately.

Figure 9:  NL843NK Fuel System.

1. The fuel system is self-bleeding. However, any

system may need manual bleeding when:
a. A new fuel filter is installed;
b. The engine has run out of fuel;
c. The fuel lines, injection pump or any other fuel

system component has been removed and
installed.

2. Loosen bleed bolt “A” (

Figure 9

) on top of the filter.

Pump hand primer “B” on fuel lift pump until pure
fuel (no bubbles) escapes from bleed bolt “A”.
Tighten bleed screw “A”.

3. Loosen bleed screw “C”. Pump hand primer “B”

until pure fuel (no bubbles) escapes. Then tighten
bleed screw “C”.

4. If the engine does not start after the above bleeding

process, loosen a fuel line at the injector while
cranking the engine with the starter motor until pure
fuel escapes. Then tighten the connection.  Do each
line one-at-a-time.

5. After the engine has started, use a piece of cardboard

to look for fuel leaks.

Содержание M843JK































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды