manualshive.com logo in svg

Northern Lights M843JK, Руководство оператора

Поделиться
Скачать
Northern Lights M843JK Скачать руководство пользователя страница 16

O843K  05/03

14

Servicing

FUELS - GENERAL

1. Use only clean, high quality fuels of the following

specifications, as defined by ASTM designation
D975 for diesel fuels:
a. Use grade no. 2 diesel at ambient temperatures

above freezing 32

°

F (0

°

C).

b. Use grade no. 1 at ambient temperatures below

freezing and for all temperatures at an altitude of
above 5,500 ft. (1500 meters).

2. Use fuel having less that 1% sulphur (preferably less

that 0.5%).

3. The cetane number should be a minimum of 45.
4. DO NOT use these unsuitable grades of fuel:

a. Domestic heating oils, all types.
b. Class B engine.
c. Class D domestic fuels.
d. Class E, F, G or H industrial or marine fuels.
e. ASTM-D975-60T No. 4-D and higher number

fuels.

5. Storing fuel:

a. Keep dirt, scale, water, and other foreign matter

out of fuel.

b. Avoid storing fuel for long periods of time.
c. Fill the fuel tank at the end of each day’s

operation. This will reduce condensation and
possible biological contamination.

d. If biological contamination is detected or

suspected, contact your dealer for assistance.

SP7-9.  FUEL FILTERS

1. Your generator set should have a primary fuel filter

installed. We recommend the Racor brand of fuel
filter-water separators.
a. Check the primary fuel filter daily as

recommended by the filter manufacturer.
Empty the collection bowl as necessary.

b. Change the element as often as necessary or

every 200 hours.

c. If the bowl fills with water, change the primary

and secondary element immediately.

 2. Change secondary fuel filter every 200 hours.

NOTE: The fuel filter on the engine is considered the
“secondary fuel filter.”
a. Remove the spin-on filter by turning it

counterclockwise with a filter wrench. Fill the
new cartridge with fuel and install it after
applying engine oil to gasket surface. Screw on
until the gasket surface comes into contact with
sealing surface of filter base. Then, tighten it
two-thirds of a turn by hand. Do not overtighten.

b. Fuel filter part numbers are:

843JK and 843NK    –   #130336020

Содержание M843JK































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды