manualshive.com logo in svg

Northern Lights M843JK, Руководство оператора

Поделиться
Скачать
Northern Lights M843JK Скачать руководство пользователя страница 11

O843K  05/03

9

SHUTDOWNS AND ALARMS

1. Your unit is fitted with a system to protect it from

high water temperature or low oil pressure.
a. Generator sets have shutdown systems to stop the

engine. They have no warning horns.

b. Other alarms and shutdowns are available as

optional equipment.

NOTE:  Do not rely on your warning to the
exclusion of careful gauge monitoring. Watching
your gauges can prevent damage to the unit and
dangerous power losses.

2. Do the following when your warning or shutdown

system is activated:
a. Check the temperature gauge.

Marine sets:  If above 205

°

F (96

°

C), shut off the

engine immediately.
Industrial sets:  If above 230

0

F (110

0

C) shut off

the engine immediately.

b. Use the Trouble Shooting Guide on page 22 to

isolate the cause of the overheat.

CAUTION:  Do not remove the water fill
cap of an overheated engine. Escaping high
temperature steam can cause severe burns.
Allow the engine to cool and then remove the
cap slowly using protective clothing.

d. Make repairs. Restart your Marine set after the

temperature gauge registers below 200

°

F (94

°

C).

e. Watch the temperature gauge regularly and

turn off the unit if the temperature rises
above 205

°

F (96

°

C) on Marine units.

Repeat troubleshooting.

3. If shutdown is activated and the temperature gauge

shows temperature within normal temperature range:
a. Check the engine crankcase oil level.
b. If the oil level is low, fill with recommended

lubricating oil and restart. Watch the oil pressure
gauge carefully and shut off the engine if it does
not show a normal reading (20-60 PSI) after a
few seconds of operation.

c. If the oil level is normal, DO NOT restart the

engine. Call your dealer for assistance.

SPARE PARTS

1. ADE recommends that you keep the following spare

parts on hand for field service. The parts are
available from your local Northern Lights dealer.
Some marine models already have “On-Board-Kits,”
a handy box that contains the most common parts
you will need.

2. All owners should have the following spares:

a. Primary and secondary fuel filter elements
b. Oil filters
c. Air filter
d. Alternator belt
e. Thermostat and gaskets
f. Seawater pump impeller & gaskets (marine only)
g. Glow plug
h. Injector and washer

3. If your set is operating a long distance from a

servicing dealer, add the following:
a. Complete set of injectors
b. Copper washers for injector change
c. Complete set of glow plugs
d. Fuel lift pump

Operating Procedures

Содержание M843JK































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды