Northern Lights L944D, M944W, NL944D2, M30CW, M944T, NL944T2, and M38CR2 Скачать руководство пользователя страница 26

26

OL944D  11/13

Troubleshooting

ENGINE

 PROBLEM 

POSSIBLE CAUSE 

RECOMMENDATION(S)

Engine Hard to Start 

 

Improper starting procedure 

• See starting section of this manual. 

or Will Not Start

  

 

No fuel 

• Check level of fuel in fuel tank. 

 

Low battery condition 

• Check electrolyte level and condition. 

 

Excessive resistance  

• Clean and tighten all battery connections.

 

in starting circuit

 

Crankcase oil too heavy 

• Use oil of proper viscosity.

 

Improper type of fuel 

• Consult fuel supplier and use proper type

 

 

  of fuel for operating condition.

 

Water, dirt or air in fuel system 

• Drain, flush, fill and bleed system.

 

Clogged primary 

• Clean or replace filter element.

 

fuel filter element

 

Clogged secondary 

• Replace filter element.

 

fuel filter element

 

Dirty or faulty injection nozzles 

• Have your dealer check injection nozzles.

Engine Runs Irregularly

 

Below normal engine temperature  • Remove and check thermostat.

or Stalls Frequently

 

 

Clogged primary 

• Clean or replace filter element.

 

fuel filter element

 

Clogged secondary 

• Replace secondary filter element.

 

fuel filter element

 

Water or dirt in the fuel system 

• Drain, flush, fill and bleed system.

 

Dirty or faulty injection nozzles 

• Have your dealer check injection nozzles.

 

Air in fuel system 

• Inspect clamps and hoses on suction side

 

 

  of fuel pump for air leak.

 

Improper type of fuel 

• Consult fuel supplier and use proper type 

 

 

  of fuel for operating condition.

Lack of Engine Power

 

Engine overloaded 

• Reduce the load.

 

Intake air restriction 

• Service air cleaner.

 

Clogged primary 

• Clean or replace filter element.

 

fuel filter element

 

Clogged secondary 

• Replace filter element.

 

fuel filter element

 

Improper type of fuel 

• Consult fuel supplier and use proper type of 

 

 

  fuel for operating conditions.

 

Overheated engine 

• See “Engine Overheats” in next category.

 

Below normal engine temperature  • Remove and check thermostat.

 

Improper valve clearance 

• Reset valves. Best done by dealer.

 

Dirty or faulty injection nozzles 

• Replace injectors. Best done by dealer.

Содержание L944D, M944W, NL944D2, M30CW, M944T, NL944T2, and M38CR2

































Отзывы: