Northern Lights L944D, M944W, NL944D2, M30CW, M944T, NL944T2, and M38CR2 Скачать руководство пользователя страница 12

12

OL944D  11/13

The Servicing Schedule Chart below shows the service schedule required for proper maintenance of your generator set. 

More detailed coverage of each Service Point (SP) is listed on the page noted in the ‘page’ column.

DAILY:

 SP1 

Check oil level in engine

 SP8 

Check primary fuel filter

 SP14 

Check cooling water level

   

Check sea strainer

AFTER FIRST 50 HOURS:

 SP2/3 

Change engine oil and filter

 SP5 

Check V-belt tension

 SP7 

Adjust valves

 SP19 

Check electrolyte level in batteries 

EVERY 50 HOURS:

 SP5 

Check V-belt tension

 SP19 

Check electrolyte level in batteries

AFTER FIRST 100 HOURS:

 SP2/3 

Change engine oil and filter

EVERY 250 HOURS:

 SP2/3 

Change engine oil and filter

 SP4 

Check air cleaner

 SP18 

Check zinc electrodes

EVERY 500 HOURS:

 SP6 

Check valve clearances

 SP9 

Change primary fuel filter element

 SP10 

Change secondary fuel filter

 SP12 

Check injectors

 SP15 

Check cooling system

 SP17 

Change impeller

 SP20 

Check state of charge of batteries

EVERY 2000 HOURS or as needed:

 SP13 

Check fuel injection pump

 SP16 

Check and clean heat exchanger

 

SP24

  Inspect starter and alternator

Servicing Schedule Chart

 

SERVICE

    

 

 

50 

100  250  500  2000

 

POINT

 

PAGE 

OPERATION 

  DAILY Hours Hours Hours Hours Hours

 ENGINE:

 

SP1 12 

Check oil level 

 

 SP2 

12 

Change engine oil

1, 5, 6

 

  

 

 

 SP3 

13

 

Change lube oil filters

1, 5

 

  

 

 

 SP4 

13 

Check air cleaner

1, 4

 

   

 

 SP5 

13 

Check V-belt tension

1

 

     

 SP7 14 

Check valve clearances

5

 

       

 FUEL SYSTEM:

 SP8 15

 

Check primary filter

2

  

 SP9 15

 

Change primary filter element

1, 3

 

       

 SP10 15

 

Change secondary fuel filter

1, 3

 

       

 SP11 16 

Bleed the fuel system

3

 

 SP12 17 

Check injectors

1

 

       

 SP13 18 

Check fuel injection pump 

 

 

 

 

 

 

 COOLING SYSTEM:

 SP14 

20 

Check cooling water level 

 

 SP15 

20

 

Check and flush cooling system

7

 

       

 

 SP16 

21 

Check and clean heat exchanger 

 

 

 

 

 

 

 SP17 

21 

Change impeller in raw water pump

1, 3

 

       

 SP18 

21 

Check zinc electrodes

4

 

     

 ELECTRICAL SYSTEM:

 SP19 

23 

Check electrolyte level in batteries

1, 4

    

 SP20 

23 

Check condition of batteries with hydrometer

1

 

       

 SP24 

24 

Inspect alternator and starter 

 

 

 

 

OUT OF SERVICE:

 SP23 

23 

Winterizing or out-of-service

3

 

1) Perform all maintenance once a year even if hour level has not been 

reached.

2) Consult manufacturer's maintenance schedule, note on chart.

3) Whenever necessary.

4) More often if necessary.

5) After first 50 hours.

6) Adjust at first 100 hours.

7) Or every 1 year

Содержание L944D, M944W, NL944D2, M30CW, M944T, NL944T2, and M38CR2

































Отзывы: