North KLASIK Series Скачать руководство пользователя страница 16

Страница: 16 / 40

SPOOL TORCH: Wear Parts & Torch Parts

May 25, 2022

Page 16

User Manual No: OM-10

A EN

SECTION 5

–

SPOOL TORCH: Wear Parts & Torch Parts

Torch installation must be

done by a suitably Trained

and Qualified Tradesperson.

Disconnect power to

MIG/MAG equipment. Elec-

tric shock can kill.

Flying metal or

dirt can injure

eyes.

FUMES and Shielding GAS can

be hazardous to your health.

Moving parts

can cause injury.

Welding wire

can cause in-

jury

Improper instal-
lation can cause

fire.

Read User

Manual.

Genuine JINAN NORTH WELDING TOOLS parts must be used for safety and performance reasons, or the warranty becomes invalid.

In-

spect all parts for transportation damage.

Do not use damaged or worn parts.

Before starting the MIG/MAG equipment, check the whole

installation according to the manufacturer's instructions, this Manual and applicable national / state / local safety regulations.

5.01

SPOOL TORCH: Change Wear Parts

a) Disconnect power to MIG/MAG equipment.
b)

Remove

---

Nozzle (1):

Remove threaded nozzle by turning in a counter clock-

wise direction OR slide

–

on nozzle can be removed using a twisting

pull action.

---

Contact Tip (2):

Cut

Welding Wire

(electrode) close to the

Contact

Tip (2)

and remove burrs before turning the

Contact Tip (2)

in a

counter clockwise direction.

---

Tip Holder (3):

Remove using an appropriate tool.

---

Gas Diffuser (4):

Remove using an appropriate tool.

---

Liner (6):

Remove the

Liner Nut (5)

, if fitted, by using an appropri-

ate wrench in a counter clockwise direction then pull the

Liner (6)

out of the

Swan Neck

Replace

---

Liner (6):

Fit the Liner in to the

Swan Neck

then secure the

Liner

Nut (5)

, if fitted, by using an appropriate wrench in a clockwise di-

rection.

---

Gas Diffuser (4):

Fit using an appropriate tool.

---

Tip Holder (3):

Fit using an appropriate tool.

---

Contact Tip (2):

Fit the contact tip turning the

Contact Tip (2)

in a

clockwise direction.

---

Nozzle (1):

Fit the threaded nozzle by turning in a clockwise direc-

tion OR slide

–

on nozzle can be fitted using a twisting push action.

5.02

SPOOL TORCH: Nozzles, Contact Tips, Contact Tip Holders, Gas Diffusers, and Liners
Parts

NOZZLES

Disconnect

Содержание KLASIK Series









































Результаты поиска

Содержание KLASIK Series

Отзывы:

Похожие инструкции для KLASIK Series

Бренды по названию

Популярные бренды

North KLASIK Series, Руководство по эксплуатации

Результаты поиска

Содержание KLASIK Series

Отзывы:

Похожие инструкции для KLASIK Series

Бренды по названию

Популярные бренды