SPOOL TORCH: Installation and Operation
May 25, 2022
Page 12
User Manual No: OM-10
4
A EN
SECTION 4
–
SPOOL TORCH: Installation and Operation
4.01
SPOOL TORCH: Environmental Limits
These
air-cooled MIG/MAG Manual Welding Torches are
designed for use in environments where:
•
Operating temperature range is -10 °C to +40 °C
(+14 °F to +104 °F)
•
Relative air humidity during operating is 0% to 90% @
+ 20 °C ambient air temperature
4.02
SPOOL TORCH: Operation Guidelines
Be sure to locate the MIG/MAG equipment according to
the following guidelines:
•
In areas, free from moisture and dust.
•
In areas, free from oil, steam, and corrosive gases.
•
In areas, not subjected to abnormal vibration or shock.
•
In areas, not exposed to direct sunlight or rain.
Torch installation must be
done by a suitably Trained
and Qualified Tradesperson.
Disconnect Power to
MIG/MAG equipment. Elec-
tric shock can kill.
Flying metal or
dirt can injure
eyes.
FUMES and Shielding
GAS can be hazardous
to your health.
Moving parts
can cause in-
jury.
Sparks, weld spatter or
hot work piece can
cause fires and burns.
Improper instal-
lation can cause
fire.
Read User
Manual.
Genuine JINAN NORTH WELDING TOOLS parts must be used for safety and performance reasons, or the warranty becomes
invalid.
Inspect all parts for transportation damage.
Do not use damaged parts.
4.03
SPOOL TORCH: Connecting Torch Power Pin to MIG Equipment Adaptor
For Spool Torches QLBF-200 III-6E, QLBF-200 III-8E, QTLB-24D-SP-6E, QTLB-24D-SP-8E, QTLB-36D-SP-6E, QTLB-36D-SP-8E.
Euro Power Pin Connector Block to Euro Style Adaptor
a) Disconnect Power to the MIG/MAG equipment.
b) Align
Euro Power Pin Connector Block
with
Euro Torch Adaptor
then insert it.
c) Secure tighten the
Connector Nut
into the
Euro Adaptor
.
d) Connect the Multi-Pin Plug to the MIG/MAG equipment Control Socket.
For Spool Torches QLBF-200 III-6T, QLBF-200 III-8T, QTLB-24D-SP-6T, QTLB-24D-SP-8T, QTLB-36D-SP-6T, QTLB-36D-SP-8T.
Tweco
®
Power Pin Connector Block to Tweco Style Adaptor
a) Disconnect Power to the MIG/MAG equipment.
b) Insert the
Tweco Power Pin
into the
Tweco Torch Adaptor
to shoulder then se-
cure using mechanical means as described in MIG/MAG equipment user man-
ual.
c) Connect the Multi-Pin Plug to the MIG/MAG equipment Control Socket.
For Spool Torches QLBF-185-6, QLBF-185-8.
Spool Torch is
Hard Wired to MIG/MAG equipment
a) Disconnect Power to the MIG/MAG equipment.
b) Refer to the MIG/MAG equipment Operating Manual to identify the connection points for the 4-pin plug, power cable with 13mm lug, and 5mm (inside
diameter) gas hose.
c) Connect power cable with 13mm lug to the MIG/MAG equipment Positive Weld Terminal as described in the MIG/MAG equipment Operating Manual.
d) Connect 5mm (inside diameter) gas hose to the MIG/MAG equipment gas hose as described in the MIG/MAG equipment Operating Manual.
e) Connect the Multi-Pin Plug to the MIG/MAG equipment Control Socket.
Disconnect
