manualshive.com logo in svg

North Star M157310AC.1, Руководство пользователя

Поделиться
Скачать
North Star M157310AC.1 Скачать руководство пользователя страница 34

Burner Adjustment 

 

34 

Oil Burner Adjustment 

      

(only needed if white exhaust smoke appears)

 

The oil burner is preset and performance tested at the factory (elevation 1100 feet).  Different 
altitudes may require a one-time initial burner adjustment. 

 

     

CAUTION:   

If white smoke appears from the burner exhaust vent during start-up or operation, discontinue 
use and readjust air bands.

 

 

 

Specific steps for burner correction are given below. 

Burner 
Correction

 

Adjusting the burner will require you to access the burner from underneath the 
pressure washer while someone else is operating the spray gun.   

 

Detailed instructions: 

 

1.

 

Make sure burner is cool to the touch before attempting to adjust. 

 

      WARNING

:  

The burner adjustment procedure requires part of 

an individual's body to be underneath the pressure washer while it is 
elevated.  Always ensure the pressure washer is securely elevated 
before working on the burner underneath.  

 

2.

 

Locate the air intake adjustment band as shown in Figure 13 below. Observe 

the position of the arrow on the air band relative to the calibration numbers 
directly to the right.  (Note: Factory calibration starts out at close to "1".)  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

 

Loosen the locking screw and rotate the air band closed until black smoke 

appears from the burner exhaust vent.  Note which number the arrow now 
points to. 

4.

 

Slowly open the air band until white smoke just starts to appear. 

5.

 

Turn air band halfway back to the black smoke position previously noted.  

Tighten the locking screw. 

Figure 13 

 

 

Locking 

Screw 

Rotatable Air 

Intake Adjustment 

Band 

Arrowhead 

Burner 

Содержание M157310AC.1

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды