background image

Before Each Use 

 

15 

 
Follow the steps below prior to each use of the pressure washer. 
 

 

Steps to Follow Before Each Use 

Step 1.  Check Equipment  

Step 2.  Add Fuel(s) 

Step 3.  Select Suitable Worksite 

 

 

Step 1. Check Equipment 

Check/add 
pump oil 

Check/add pump oil

Caution: Never run the pump without sufficient lubrication!  

 

1.

 

Check oil level.  Verify that oil level is half way up the sight glass.  

2.

 

If oil level is low, fill using SAE30 non-detergent oil or Cat Pump Oil Item 
#22158.  

3.

 

Replace fill cap.

 

Check/add 
engine oil 

Check the engine oil level and add oil as needed. 

  

Use the recommended oil type for your engine and expected ambient conditions.   
(See engine Owner's Manual for oil type and capacity, and more detailed oil 
check/fill instructions.) 

 

      

WARNING:  Burn hazard 

Never open oil port while engine is running.  Hot oil can spray over face 
and body. 

˙ 

Notes:   

o

 

Low oil shutdown feature prevents the engine from starting without sufficient 
oil.   

o

 

Engine is shipped without oil.  You must add oil before first use. 

 

Inspect spray 
system 

Always inspect spray system for damage and leaks before each use. 

Do not start pressure washer until all needed repairs have been completed. 

 

 

     WARNING

:  

High pressure fluid injection hazard

 

High-pressure fluid discharge from leaks (even pin-sized) or ruptured 
components can pierce skin and inject fluid into the body.  Injection 
injury can result in blood poisoning and/or severe tissue damage leading 
to infection, gangrene, and possibly amputation.  

 

Never use a finger or skin to check for leaks.   

 

Never operate machine with damaged or missing hoses/parts. 

 

Never attempt to repair a high-pressure hose or component – Always 
replace it with a part that is rated at or above the pressure rating of this 
machine. 

 

 

Содержание M157310AC.1

























































Отзывы: