manualshive.com logo in svg

North Star M157310AC.1, Руководство пользователя

Поделиться
Скачать
North Star M157310AC.1 Скачать руководство пользователя страница 13

Assembly and Initial Set-Up 

 

13 

 

Step 4. Battery Installation 

 

Install a 12-volt standard lawn and garden battery (Group U1) with a minimum 18 amp-
hour rating.  

The engine will run, but the burner will not fire unless a battery is installed. 

 

 

The battery is to be supplied by the customer and should be installed in the protective battery 
compartment located near the engine.   

 

Follow the steps below for connecting and disconnecting the battery.   

 

 

      

WARNING

:  Battery Hazards 

Batteries are hazardous because they contain caustic acid, can emit explosive gases, and can 
cause electric shock.  Caution must be exercised when making connections to a battery to 
avoid shock and contact with the acid, and to prevent any sparking that could lead to an 
explosion.  ALWAYS follow the general battery safety rules and instructions listed below. 

 

General 
Battery 
Safety Rules

 

 

ALWAYS  use  eye  protection  and  protective  clothing  when  handling 
batteries. 

 

NEVER smoke or work near sparks or other sources of ignition. 

 

NEVER touch both battery terminals at the same time with your hand or any 
non-insulated tools.

 

 

If battery acid contacts skin or clothing, flush immediately with water and 
neutralize with baking soda. 

Connecting 
the battery 

Always connect the cables in the following sequence to avoid possible shock: 

 

1.  Find the battery cables located inside the battery compartment. 
2.  Connect the 

red

 

cable to the 

positive

 (+)

 terminal of the battery. 

3.  Then connect the 

black

 cable to the 

negative

 (-)

 terminal of the battery. 

 

Disconnecting 
the battery 

Always disconnect cables in the following sequence to avoid possible shock. 

 

1.  First, disconnect the 

black

 cable from the 

negative

 (-)

 terminal of the 

battery. 

2.  Next, disconnect the 

red

 

cable from the 

positive

 (+)

 terminal of the battery. 

3.  Remove the battery from the battery compartment. 
 

Содержание M157310AC.1

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды