Nortel Passport 4400 Series Скачать руководство пользователя страница 62

Страница: 62 / 144

Ethernet Base Module and Interface Modules

Passport 4400 Hardware Installation Manual

5-4

56kbps CSU/DSU Interface Module

The 56kbps module supports the Dataphone Digital Service (DDS) without the
secondary signaling channel. This interface module supports the following
loopback modes:

• DSU loopback

• CSU loopback

• digital loopback

• local loopback

• local loopback transmit end (LLT)

• local loopback receive end (LLR).

The 56kbps CSU/DSU interface module may only be used in the Port 2 (MPANL
port) slot. Do not place the 56kbps module in Port 3.

Figure 5-5. Front and Back View of 56kbps CSU/DSU Interface Module

An 8-position RJ48C jack is provided to interface with the DDS network.

Figure 5-6. 56kbps CSU/DSU Connector

Note: The interface module must be inserted into the

unit with the component side facing down.

Rear View

Pin 1

RJ48

1
2

4
5
6
7
8

RJ48 Pin Assignments

Transmit Data from Network

Receive Data to Network

Pins 3, 4, 5, 6 Not Connected

Содержание Passport 4400 Series

















































































































































Результаты поиска

Содержание Passport 4400 Series

Отзывы:

Похожие инструкции для Passport 4400 Series

Бренды по названию

Популярные бренды

Nortel Passport 4400 Series, Руководство по установке оборудования

Результаты поиска

Содержание Passport 4400 Series

Отзывы:

Похожие инструкции для Passport 4400 Series

Бренды по названию

Популярные бренды