Nortel Passport 4400 Series Скачать руководство пользователя страница 112

Страница: 112 / 144

Indicators

Passport 4400 Hardware Installation Manual

11-2

T1/E1 Voice Module

There are 13 indicators associated with the T1/E1 Voice Module -- six for the
Digital Voice channels, and seven for the Voice Module.

Figure 11-3. T1/E1 Access Module Indicators

Digital Voice Channel Status Indicators

Indicators 1 through 6 represent, respectively, the status of the digital voice
channels B1 through B6, as follows:

Table 11-2. Digital Voice Channel Status Indicators

State

Status

Off

Digital Voice Module not installed or defective, or power is off

Green

Digital voice channel is connected, and active voice call is in progress

Flashing green

Test in progress

Quick-flashing green

Download in progress

Amber

Idle (both ends on-hook)

Flashing amber

Fax call in progress

Red

Waiting for code download

Flashing red

Busy

Quick-flashing red

Alarm/Test Failure

Digital Voice Channel

Status Indicators

T1/E1 Status

Indicators

T1:

E1:

Содержание Passport 4400 Series

















































































































































Результаты поиска

Содержание Passport 4400 Series

Отзывы:

Похожие инструкции для Passport 4400 Series

Бренды по названию

Популярные бренды

Nortel Passport 4400 Series, Руководство по установке оборудования

Результаты поиска

Содержание Passport 4400 Series

Отзывы:

Похожие инструкции для Passport 4400 Series

Бренды по названию

Популярные бренды