Nortel BCM50 2.0 Скачать руководство пользователя страница 9

Страница: 9 / 86

Chapter 1 Getting started with telephony devices

Telephony Device Installation Guide

BCM50 applications

BCM50 Release 2.0 supports many applications provided on the existing BCM50 platform.

•

Voice Messaging for standard voice mail and auto-attendant features

•

Unified Messaging, providing integrated voice mail management between voice mail and
common e-mail applications

•

Fax Suite, providing support for attached analog fax devices

•

voice networking features

•

LAN (computer telephony engine) CTE

•

VEWAN

•

Interactive Voice Response (IVR)

•

IP Music

•

Contact Center

Symbols and text conventions

These symbols are used to Highlight critical information for the

Administration Guide

(N0060598)

system:

Note:

You enable the following features by entering the appropriate keycodes (no

additional hardware is required)

Caution:

Alerts you to conditions where you can damage the equipment.

Danger:

Alerts you to conditions where you can get an electrical shock.

Warning:

Alerts you to conditions where you can cause the system to fail or work

improperly.

Note:

A Note alerts you to important information.

Tip:

Alerts you to additional information that can help you perform a task.

Содержание BCM50 2.0























































































Результаты поиска

Содержание BCM50 2.0

Отзывы:

Похожие инструкции для BCM50 2.0

Бренды по названию

Популярные бренды

Nortel BCM50 2.0, Руководство по установке

Результаты поиска

Содержание BCM50 2.0

Отзывы:

Похожие инструкции для BCM50 2.0

Бренды по названию

Популярные бренды