Nortel BCM50 2.0 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 86

background image

30

Chapter 5 ISDN overview

NN40020-309

NN40020-309

An analog modem operating at 14.4K takes about 4.5 minutes to transfer a 1MB data file and a
28.8K modem takes about half that time. Using one channel of an ISDN line, the transfer time is
reduced to only 1 minute and if two ISDN channels are used, transfer time is just 30 seconds.

When transmitting data, the connect time for an average ISDN call is about three seconds per call,
compared to about 21 seconds for the average analog modem call.

Types of ISDN service

Two types of ISDN services (lines) are available: Basic Rate Interface (BRI) and Primary Rate
Interface (PRI). Each line is made up of separate channels known as B and D channels which
transmit information simultaneously.

•

BRI is known as 2B+D because it consists of two B-channels and one D-channel.

•

PRI is known as 23B+D(in North America) or as 30B+D (in Europe). In North America,
23B+D consists of 23 B-channels and one D-channel (T1 carrier). In Europe, 30B+D consists
of 30 B-channels and one D-channel (E1 carrier).

B-channels:

B-channels are the bearer channel and are used to carry voice or data information and

have speeds of 64 kb/s. Since each ISDN link (BRI or PRI) has more than one B-channel, a user
can perform more than one transmission at the same time, using a single ISDN link.

D-channels:

The standard signaling protocol is transmitted over a dedicated data channel called

the D-channel. The D-channel carries call setup and feature activation information to the
destination and has speeds of 16 kb/s (BRI) and 64 kb/s PRI. Data information consists of control
and signal information and for BRI only, packet-switched data such as credit card verification.

ISDN layers

ISDN layers refer to the standards established to guide the manufacturers of ISDN equipment and
are based on the OSI (Open Systems Interconnection) model. The layers include both physical
connections, such as wiring, and logical connections, which are programmed in computer
software.

When equipment is designed to the ISDN standard for one of the layers, it works with equipment
for the layers above and below it. There are three layers at work in ISDN for BCM50. To support
ISDN service, all three layers must be working properly.

•

Layer 1: A physical connection that supports fundamental signaling passed between the ISDN
network (your service provider) and the BCM50 system. When the LED on a BRI S/T Media
Bay Module configured as BRI is lit, your layer 1 is functioning.

•

Layer 2: A logical connection between the central office or the far end and the BCM50 system.
Without Layer 2, call processing is not possible.

«
...
28
29
30
31
32
...
»

Содержание BCM50 2.0























































































Отзывы:

Нет отзывов

Похожие инструкции для BCM50 2.0

Бренд: Samsung Страницы: 123

StarPoint 500 Entry

Бренд: 2N Страницы: 59

3300 IP 5312 IP

Бренд: Mitel Страницы: 10

Бренд: Avaya Страницы: 6

Бренд: Karel Страницы: 69

Бренд: Alcatel Страницы: 2

Бренд: iData Страницы: 38

Бренд: Gigo Страницы: 22

Бренд: jablotron Страницы: 11

Бренд: Swisscom Страницы: 106

Бренд: Kyocera Страницы: 67

Бренд: Zte Страницы: 113

Mi Note 10 Lite

Бренд: Xiaomi Страницы: 101

Бренд: WOO Страницы: 11

Бренд: i-onik Страницы: 49

Бренд: Sharp Страницы: 121

Бренд: Sharp Страницы: 134

Бренд: Sharp Страницы: 178

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды