background image

March 16, 2004

External-Antenna Nortel Networks WLAN - Access Point 

Quick Installation Guide

External-Antenna Nortel Networks WLAN - Access Point Quick Installation Guide

System Release 2.0

This Guide contains several sections allowing you to install an AS-1200-BG-EXT or AS-1200-ABG-EXT 
Nortel Networks WLAN - Access Point or an AS-1200-ABG-EXT-RE Nortel Networks WLAN - Remote 
Edge Access Point (Remote Edge Access Point). These models contain internal 802.11a and 802.11b/g 
antennas and connectors for optional external 802.11a and 802.11b/g antennas.
If you are installing an AS-1200-BG-INT or AS-1200-ABG-INT Nortel Networks WLAN - Access Point 
with internal 802.11a and 802.11b/g antennas and no connectors for optional external antennas, 
please refer to the Internal-Antenna Airespace Access Point Quick Installation Guide. 

Overview

 

Step 1: Collecting Required Tools and Supplies

 

Step 2: Configuring the Nortel Networks WLAN - Access Point or Remote Edge Access Point 
Before Installation

 

Step 3: Preparing Mounting Locations

 

Step 4: Mounting the Nortel Networks WLAN - Access Points

 

Step 5: Returning MAC Information

 

Planning Notes

 

FCC Statements for Nortel Networks WLAN - Access Points

 

ATTENTION!

Special Considerations

While Nortel Networks WLAN - Access Points have been engineered for easy installation, there are some 
guidelines that are very important to the end users:

PLACE Nortel Networks WLAN - Access Points NO MORE THAN 140 FEET APART FROM EACH 
OTHER. Placing Nortel Networks WLAN - Access Points further apart almost always results in 
poor coverage.

DO NOT MOUNT Nortel Networks WLAN - Access Points OUTSIDE BUILDINGS.

DO NOT MOUNT Nortel Networks WLAN - Access Points ON BUILDING PERIMETER WALLS 
UNLESS THE OPERATOR WANTS TO PROVIDE COVERAGE OUTSIDE THE BUILDING.

MAKE SURE that plenum-mounted Nortel Networks WLAN - Access Points and Remote Edge 
Access Points are powered using Power Over Ethernet (POE) to comply with safety regulations.

Содержание AS-1200-ABG-EXT





























Отзывы: