background image

Meridian 1

ISDN Basic Rate Interface 

Installation

Document Number: 553-3901-200
Document Release: Standard 7.00
Date: January 2002

Year Publish FCC TM

Copyright © 1992–2002 Nortel Networks
All Rights Reserved

Printed in Canada

Information is subject to change without notice. Nortel Networks reserves the right to make changes in design 
or components as progress in engineering and manufacturing may warrant. This equipment has been tested 
and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules, and the 
radio interference regulations of Industry Canada. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a commercial environment. This equipment 
generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the 
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a 
residential area is likely to cause harmful interference in which case the user will be required to correct the 
interference at their own expense.

SL-1 and Meridian 1 are trademark of Nortel Networks.

Содержание 553-3901-200

















































Отзывы: