Nortel 5399 Скачать руководство пользователя страница 66

Страница: 66 / 126

Nortel Networks 5399 Access Switch Hardware Installation Guide

Chapter 2

Installing the Model 5399 Remote Access Concentrator Module

2-34

Invoking the Console Monitor

After the image boots, you can invoke the Console Monitor by
pressing

on the service port terminal. The following prompt

appears:

Console monitor:

At the Console Monitor prompt, entering help or ? displays the available
options:

•

afd (displays the status of the Automatic Firmware
Download process - used only for the WAN interfaces).

•

cli (starts the Command Line Interpreter on the current port)

•

dump (from the Remote Access Concentrator to the host
and reboots).

•

help or ? (displays the available options).

•

info (displays configuration information for the Annex).

•

leds (displays the current front panel LED status).

•

quit (quits and returns to quiet console)

•

reboot filename (reboots the Annex).

•

rom (returns the Remote Access Concentrator to the ROM
Monitor).

•

syslog (displays syslog messages).

Return

Содержание 5399































































































































Результаты поиска

Содержание 5399

Отзывы:

Nortel 5399, Руководство по установке оборудования, Страница: 66 / 126

Результаты поиска

Содержание 5399

Отзывы: