manualshive.com logo in svg

Nortel 2340, Руководство по настройке

Поделиться
Скачать
Nortel 2340 Скачать руководство пользователя страница 35

Nortel WLAN Location Engine 2340 Web GUI

35

Nortel WLAN - Location Engine 2340 Configuration - Using Interfaces

 Using the Calibration RF Fingerprints Page

After entering the admin user name and password established at installation, repeat the following procedure for each RF 
fingerprint to capture the RF fingerprint data:

1

Select the 

Calibration>RF Fingerprints

. The following window appears.

2

If the RF fingerprint to be captured was previously created, select it from the left panel. It was not 
previously done, then click 

Add

. The default name 

New RF Fingerprint

 appears in both columns, and 

calibration controls are added to the RF Fingerprint Information column.

3

In the RF Fingerprint Information column, replace the default name 

New RF Fingerprint

 with a name 

that describes the location of the RF fingerprint, for example mailroom-nw.

4

Select the correct Locale from the 

Bound to Locale

 drop down list. An RF fingerprint can be bound to 

only one locale.

5

Enter the 

MAC Address

 of the wireless device being used to calibrate, as hex pairs separated by a colon 

(:).

6

Click 

Start

. The message ‘Buffering...’ displays, after which a flashing Progress label indicates the 

percent complete, and a graph shows the signal strength for the RF fingerprint as seen by each Location 
AP.

Note.  

If the buffering continues for more than 60 seconds, make sure the correct MAC 

address is entered

.

Содержание 2340













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды