background image

19

Combination Potable Water and Space Heating System

Isolation
Kit(*1)

Gas Supply

Backflow Preventer
(optional)

Check
Valve(*3)

Cold Water
Supply

Mixing Valve(*5)

Hot Water

Pump(*2)

Flow Switch(*4)

Fixtures

Air Handler

Optional
Expansion Tank(*6)

Recirculation System

Cold Water Supply

Isolation
Kit(*

)

Gas Supply

Aquastat(*2)

Hot Water

Optional 8-10 Gallon
Storage Tank
(To alleviate cold water sandwich)

Globe
Valve

Pump(*1)

Expansion Tank
(Install according
to local code)

Fixtures

Hot Water Return

R

B

W

Pump

120VAC

105

Neutral
Ground

Live

S

Use Honeywell Aquastat 

(Model L6006A or L6006C)

Aquastat Wiring

Notes:

1. Size the pump to provide a maximum of 1.5GPM 
    (5.7L/min.) through the system at 10ft (0.3m) of 
    head plus piping losses. 
    Adjust the flow using a globe valve and verify the 
    flow rate with the maintenance monitors.

2. Set the Aquastat to 10˚F below the set output temperature. 
    An aquastat is the minimum pump control requirement
    in order to maintain the full recirculation waranty.

3. Noritz recommends the use of an Isolation Kit
    with the installation.
    These kits include an integrated shut-off and service 
    valve with unions and a pressure relief valve. 

Notes:

1. Noritz recommends the use of an Isolation Kit with
    the installation.
    These kits include an integrated shut-off and service 
    valve with unions and a pressure relief valve.

2. Size the pump to provide a maximum of 2 GPM
    (7.5 L/min.) with a head pressure equal to the loss 
    through the water heater and Air Handler.

3. Check valve required if it is not included with the pump.

4. Set the flow switch to deactivate the Air Handler when
    the domestic hot water flow reaches 2 GPM (7.5 L/min.).
    Adjust as necessary to prevent cycling.  

5. If the system requires water for space heating at a higher 
    temperature than for other uses, means such as a
    mixing valve shall be provided to temper the water for
    the other uses to help prevent scalding.

7. The water heater cannot be used for space heating 
    applications only.
8. Only POTABLE water may be plumbed through
    the water heater.

6. Expansion tank required if a backflow preventer is installed.

NORITZ

Condensing
Tankless Gas

Water Heater

NORITZ

Condensing
Tankless Gas

Water Heater

If the Air Handler does not control the water flow automatically, the Scale detection feature will not work.

10.

 

Plumbing Applications

▲The illustration is an example. Please check with the actual water heater about the position of piping, and form.

Содержание ecoTOUGH NRC661A-OD





























Отзывы: