16
from an authorized Noritz wholesaler.
located
** Connect the blue connector marked "FLUSH" for flushing on the Circuit Board when flushing the Heat Exchanger.
7. Place the both drain hoses (H2 and H3) into the bucket filled with the flushing solution.
1. Close the gas supply valve.
2. Close the water inlet valve (V1) and the water outlet valve (V2).
3. Connect the one drain hose (H1) to the drain valve (V3), and then the other to the circulating
pump.
4. Connect the drain hose (H2) to the circulating pump.
5. Connect the drain hose (H3) to the drain valve (V4).
After connecting it, the water heater is set to “Flushing Mode”.
This procedure is only intended for use by a qualified service professional or authorized Noritz
Service Representative. Any unauthorized use of this procedure may result in voiding the
warranty.Please contact Noritz America (866-766-7489) for additional support.
Procedure for Flushing the Heat Exchanger
8. Open the both drain valves (V3 and V4).
1. Open the Front Cover.
2. Connect the blue connector***** marked "FLUSH" for flushing on the Circuit Board.
3. Then the code “CCC” is displayed on the
㻰㼍㼠㼍㻌㻰㼕㼟㼜㼘㼍㼥
4. Turn on the circulating pump to circulate the flushing solution through the water heater
for 1 hour at a rate of 1.5 gallons per minute or more.
5. The code “C60” is displayed on the Data Display when the water heater detects the flow of the
fflushing solution.
When 1 minute passes, the code “C60” will change to “C59” on the Data Display.
Detects the flow
1 minute passes
Please check whether the reverse connection of the hose (H1) and (H3) if the display number will not change.
In that case, the flow rate of the flushing solution may be under 1.5 gallons per minute.
6. When 1 hour passes, the code “C00” is flashing on the Data Display.
Do not disconnect the blue connector marked "FLUSH" for flushing on the Circuit Board.
7. Turn off the circulating pump.
The flushing solution needs to be rinsed and cleaned out of the water heater.
Below is the way to rinse and clean the flushing solution.
1. Remove both drain hoses (H2 and H3) from the bucket. And then place the drain hose (H3)
into the sink or outside to drain.
2. Close the drain valve (V3) and then open the water inlet valve (V1).
Do not open the fresh water outlet valve (V2).
3. Clean the water heater with fresh water for 3 minutes or more.
(Needs to have enough time to clean the water heater.)
4. Close the drain valve (V4) and then remove the drain hose (H3)
from the drain valve (V4).
5. Remove the drain hose (H1) from the drain valve (V3).
8. Open the gas supply valve and water outlet valve (V2).
9. Check for correct operation of the water heater.
6. Disconnect the blue connector marked "FLUSH" for flushing
on the Circuit Board.
The code “C00” goes out on the Data Display.
7. Close the Front Cover.
If the error code “C #*~C #*” is flashing on the Display Window, it means there is Scale Build-up
in the Heat Exchanger.The Heat Exchanger needs to be flushed** to remove the Scale Build-up.
Damage to the water heater due to Scale Build-up is not covered by the water heater's warranty.
To clear the error code “C #*~C #*”, the Heat Exchanger must be flushed.
If the error code “C #*” is displayed and flashing in the Display Window, please contact Noritz
America (866-766-7489).
6. Pour 1 gallon of "Calcium, Lime and Rest Removal Product"*** and 1 gallon water into the bucket.
***Notriz recommends "Calcium, Lime and Rest Removal Product" for flushing.
