background image

OBSOLETE

21-37

Issued 7/96

1

Nordson Corporation

OPERATOR’S CARD

P/N 108 885B

Model WM-1 Manual Waterborne Air Spray Gun

Safety

The following symbols warn against dangers or
possible sources of danger.  Become familiar with
them!  Failure to heed a warning symbol could lead to
personal injury and/or damage to the unit or other
equipment.

Heed all warning symbols that appear in this
document, the operator’s manual, or on the
equipment.

WARNING:  Allow only qualified personnel to
perform the following  tasks.  Observe and
follow the safety instructions in this document
and all other related documentation.

WARNING:  Risk of electrical shock.  Spray
gun operation  requires the use of a grounding
air hose and a high-dielectric strength fluid
tube.  Failure to observe this warning may
result in personal injury, death, or equipment
damage.

WARNING:  System or material pressurized.
Relieve pressure.  Failure to observe may
result in serious burns.

WARNING:  Ignition hazard.  Do not use this
handgun to  spray coating materials having a
fire point below 60 

_

C (140 

_

F).  Failure to

observe this warning may result in serious
injury and equipment damage.

CAUTION:  Use only clean dry air.  Failure to
observe this caution may reduce  electrostatic
efficiency and cause equipment damage.

WARNING:  Wear protective clothing, safety
goggles, and approved respiratory protection.
Failure to observe may result in serious injury.

CAUTION:  Do not over tighten parts.  Failure
to observe this caution may result in equipment
damage.

S

Always follow instructions in the material supplier’s
Material Safety Data Sheet (MSDS) or material
information sheet.

Introduction

This operator’s card contains only the information
necessary for installation, daily operation and
maintenance.  For other information, refer to the
manual.

The WM-1 spray gun operates with an Iso-Flo HD

Voltage Block unit (Iso-Flo).  Each installation must
meet the following requirements:

S

The system, including the electrostatic power
supply, must be installed properly and in good
working condition.

Содержание WM-1









Отзывы: