Nordson Spectrum HD Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 40

Nordson Spectrum HD Скачать руководство пользователя страница 18

Installation

3-1

Part 7169651_01

E

2012 Nordson Corporation

Section 3

Installation

WARNING:

Allow only qualified personnel to perform the following tasks.

Follow the safety instructions in this document and all other related
documentation.

Unpacking

Upon receipt, unpack the Spectrum HD feed center carefully to avoid
damage. Report any damage immediately to the shipper and to your
Nordson representative. Save packing materials for possible later use, or
dispose of properly according to local regulations.

Preparing for Installation

Position the Spectrum HD feed center on a level floor, according to the
general layout drawing supplied by Nordson application engineering. Use
the leveling pads to level the feed center.

To ensure easy maintenance, provide a clear operating and access zone of
at least 1m (3 ft) wherever possible.

Damper Installation

A butterfly damper should be installed in the ductwork to the afterfilter. A
damper is supplied with the unit.

Extraction Duct Connection

Connect ductwork from the afterfilter/fan section to the Spectrum HD feed
center with a properly sized transition duct. A rectangular transition duct is
supplied with the unit.

Electrical Connections

CAUTION:

Equipment damage may occur if the electrical panel is

connected to any line voltage other than that stated on the identification
plate.

«
...
16
17
18
19
20
...
»

Содержание Spectrum HD









































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды