background image

20

0

5

POWER

RUN

SETUP

CYCLE

Test

Clear

Purge

Run

Setup

Program

Fast

Slow

Time Set

Steady

Fast

Slow

Time Set

STOP

Pressure

Time

®

A NORDSON COMPANY

To pressurize

To exhaust

0 0

1

0

1

0

2

0

2

0

30

30

40

40

50

50

60

60

7070

808

0

9

0

9

0

100

10

0

7

7

6

6

5

5

4

4

3

3

2

2

1

1

0 0

1

0

1

0

2

0

2

0

30

30

40

40

50

50

60

60

7070

808

0

9

0

9

0

100

10

0

7

7

6

6

5

5

4

4

3

3

2

2

1

1

Installation

Open the valve with an air pulse
long enough to fill the valve and
start fluid flow. Test the dispensed
amount with a nominal time setting.

11

Set desired deposit size by changing
tip size, reservoir pressure, needle
stroke and valve open time.

12

1.

Mount valve with an EFD universal valve
mount (#7002VM) or other fixture.

2.

Connect valve control air line to
ValveMate

controller (or other pneumatic

switch) used to control operating air to
the valve.

3.

Connect the white male quick-connect
on the flexible air line to the white female
quick-connect at the air pressure regulator.

4.

Install the barrel reservoir on the fluid
inlet fitting (installed for use with 

Ultra

®

barrel reservoirs). For low viscosity fluids,
fill the reservoir after installing it on the
fluid-inlet fitting. High viscosity materials
can be loaded into the reservoir before
installing on the inlet fitting.

Note:

Fill barrels no more than 2/3 full. Always
use a SmoothFlow

piston when dis-

pensing medium to high viscosity mate-
rials (see setup illustration).

5.

Attach the barrel adapter head to the
barrel reservoir using air interconnect
coupler to connect the barrel adapter
assembly to the flexible air line.

6.

Install appropriate size EFD SafetyLok

dispensing tip on the tip adapter. Tighten
the tip retaining nut fully to position the
needle hub against the shoulder of the
tip adapter.

7.

Refer to back page for instructions on
calibrating the needle stroke.

8.

Open stroke adjustment knob to desired
position (1/2 turn open is the recom-
mended starting point). 

9.

Set reservoir pressure to low for thin 
fluids and higher for thick fluids. Use the
in-line air shut-off valve to pressurize or
depressurize barrel reservoir. 

10.

Set valve control air pressure at 70 
psi (4.8 bar). Refer to valve controller 
operating manual.

Open

Close

 Air Output

ut

 Exhaust

r

Prior to installing this valve, please read the
associated reservoir and valve controller
operating instructions to become familiar
with the operation of all components of the
dispensing system.

5

2

4

0

1

0

2

0

30

40

50

60

70

8

0

9

0

10

0

7

6

5

4

3

2

1

0 0

101

0

202

0

30

30

40

40

50

50

60

60

7070

808

0

909

0

10

0

10

0

7

7

6

6

5

5

4

4

3

3

2

2

1

1

1

9

0 0

101

0

202

0

30

30

40

40

50

50

60

60

7070

808

0

909

0

10

0

10

0

7

7

6

6

5

5

4

4

3

3

2

2

1

1

0

1

0

2

0

30

40

50

60

70

8

0

9

0

10

0

7

6

5

4

3

2

1

10

6

0

1

0

2

0

30

40

50

60

70

8

0

9

0

10

0

7

6

5

4

3

2

1

0

1

0

2

0

30

40

50

60

70

808

0

9

0

10

0

7

6

5

4

3

2

1

3

Open

Close

7

8

adjustment knob

calibration knob

Содержание 741MD-SS Series

Страница 1: ...ire small dispensing tips from 22 to 33 gauge The 741MD SS provides exceptional control and the absolute minimum dead fluid volume 741MD SS Series Dispense Valve INSTALLATION GUIDE Control air hose Dispensing tip Inlet fitting Barrel adapter assembly Barrel reservoir Stroke reference ring Fluid body A NORDSON COMPANY Electronic pdf files of EFD manuals are also available at www efd inc com manuals...

Страница 2: ... when dis pensing medium to high viscosity mate rials see setup illustration 5 Attach the barrel adapter head to the barrel reservoir using air interconnect coupler to connect the barrel adapter assembly to the flexible air line 6 Install appropriate size EFD SafetyLok dispensing tip on the tip adapter Tighten the tip retaining nut fully to position the needle hub against the shoulder of the tip a...

Страница 3: ...ontrol Pad set time timer bypass display pressure psi bar TEACH program test cycle purge reset air input power input voltage selector air output to valve I O connector with alarm output 60 psi connector for optional foot pedal Rear Panel Pressure Time Toggle open closed Input air pressure at 70 psi 4 8 bar retracts the piston and needle from the needle seat in the dispensing tip permitting fluid f...

Страница 4: ...ositioned or reset to the zero mark use the following procedure A Remove the dispensing tip if installed B Turn the small knob counterclockwise one full turn C Turn the large knob clockwise until it stops If the zero on the reference ring does not line up with the index mark continue with the following steps D Loosen the small set screw located on the reference ring E Rotate reference ring until i...

Отзывы: