30
PART LIST—Model No. NTL01409.1
R0410A
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
17
#8 x 1/2" Screw
2
4
#8 x 1" Tek Screw
3
1
3/8" x 2" Bolt
4
6
5/16" x 1 1/2" Patch Bolt
5
4
5/16" x 3/4" Patch Bolt
6
1
3/8" x 1 3/4" Patch Bolt
7
4
3/8" x 5 1/2" Patch Bolt
8
4
1/4" x 1/2" Patch Bolt
9
8
5/16" Star Washer
10
5
3/8" Nut
11
4
3/8" Star Washer
12
2
1/4" Star Washer
13
1
Pulse Crossbar
14
36
#8 x 3/4" Screw
15
2
1/4" x 1 3/4" Bolt
16
2
3/8" x 1 3/4" Bolt
17
8
#8 x 1/2" Washer Head Screw
18
12
#12 x 1" Screw
19
4
Belt Guide Screw
20
2
Drive Motor Bolt
21
4
3/8" x 2 1/8" Bolt
22
2
3/8" x 1 3/8" Bolt
23
4
5/16" x 1 1/4" Bolt
24
1
Drive Roller Bolt
25
2
1/4" Flat Washer
26
2
1/4" Lock Washer
27
2
Cage Nut
28
6
#8 x 3/4" Truss Head Screw
29
2
3/8" Jam Nut
30
4
5/16" Flange Nut
31
4
Hood Clip
32
1
1/4" Star Washer
33
2
#8 Star Washer
34
4
#8 x 1" Truss Head Screw
35
1
Left Foot Rail
36
1
Warning Decal
37
2
Platform Cushion
38
1
Walking Platform
39
2
Belt Guide
40
1
Left Foot Rail Cover
41
1
Right Foot Rail Cover
42
1
Drive Roller/Pulley
43
1
Magnet
44
1
Reed Switch
45
1
Reed Switch Clamp
46
1
Drive Motor Belt
47
1
Drive Motor
48
1
Walking Belt
49
1
Incline Sensor Wire
50
1
Right Foot Rail
51
1
Storage Latch
52
4
#8 x 1" Screw
53
1
Electronics Bracket
54
1
Controller
55
1
Frame
56
1
Idler Roller
57
1
Right Frame Foot
58
1
Left Frame Foot
59
1
Hex Key
60
1
5/32" Hex Key
61
1
Motor Hood
62
2
#8 x 1 1/2" Screw
63
2
Lift Frame Spacer
64
2
Frame Spacer
65
1
Lift Frame
66
1
Incline Motor
67
2
Incline Motor Spacer
68
2
Hood Mount
69
1
Belly Pan
70
1
Reset/Off Circuit Breaker
71
1
Power Cord
72
2
Grommet
73
1
Lift Motor Wire
74
3
Releasable Tie
75
1
15 1/2" Tie
76
11
8" Tie
77
2
Handrail Cover
78
1
Left Handrail
79
1
Right Handrail
80
2
Console Clamp
81
1
Console Frame
82
1
Left Upright
83
1
Right Upright
84
1
Base Cover
85
1
Upright Wire
86
1
Right Upright Cover
87
1
Left Upright Cover
88
4
Bolt Spacer
89
2
Caution Decal
90
1
Left Upright Spacer
91
1
Right Upright Spacer
92
4
Base Foot
93
1
Audio Wire
94
1
Base
95
2
Wheel
96
2
Wheel Housing
97
2
Wheel Axle
98
1
Key/Clip
99
8
Wire Tie
100
1
Console
7
1.
Make sure that the power cord is unplugged.
With the help of a second person, carefully tip
the treadmill onto its left side. Partially fold the
Frame (55) so that the treadmill is more stable;
do not fully fold the Frame yet.
Locate the Upright Wire (85), which is bundled
at the back of the Base (94). Remove the pack-
aging from the Upright Wire. Next, insert the
Upright Wire into the Base, and pull it out of the
indicated hole. If necessary, use the plastic tie to
pull the Upright Wire out of the hole.
Hold a Wheel (95) inside a Wheel Housing (96).
Press a Wheel Axle (97) through the Wheel.
Next, press the Wheel Housing into the Base
(94). Make sure that the tab on the Wheel
Housing is in the position shown.
Attach the other Wheel (95) in the same way.
97
97
95
96
96
Tab
1
94
55
85
2. Attach four Base Feet (92) to the Base (94) in
the locations shown with four #8 x 1" Tek Screws
(2).
See the inset drawing.
Cut the plastic tie near
the Upright Wire (85).
2
94
2
92
92
2
2
2
92
92
85
Hole
Tie
Cut
85
Tab
Tie
Tie