26
11
9. With the help of a second person, grip the sides
of the console assembly and hold it near the
Right Upright (83) and the Left Upright (not
shown).
Do not lift the console assembly by
the Right Handrail (79) or the Left Handrail
(not shown).
Connect the Upright Wire (85) to the console
wire.
See the inset drawing. The connectors
should slide together easily and snap into
place.
If they do not, turn one connector and try
again.
IF THE CONNECTORS ARE NOT CON-
NECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN YOU TURN ON THE
POWER.
Then, remove the wire tie from the
Upright Wire.
Console
Assembly
9
Console
Wire
Wire
Tie
85
79
83
85
Console
Wire
10. Slide a Handrail Cover (77) onto the lower end
of each Handrail (78, 79).
Set the console assembly on the Left and Right
Uprights (82, 83). At the same time, slide the
lower ends of the Handrails (78, 79) over the
brackets on the Uprights.
Be careful not to
pinch any wires.
Insert the excess wire into the
Right Upright.
Start four 5/16" x 3/4" Patch Bolts (5) with four
5/16" Star Washers (9) into the Uprights (82,
83). Then, start two 5/16" x 1 1/2" Patch Bolts
(4) into the Uprights.
Do not tighten the Patch
Bolts yet.
10
5
79
4
77
77
82
4
9
9
5
78
Console
Assembly
83
Bracket
Bracket
TROUBLESHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION:
a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 14). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 14.
IMPORTANT: The treadmill is not
compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
PROBLEM: The power turns off during use
SOLUTION:
a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The console screen remains lit when you remove the key from the console
SOLUTION:
a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the screen remains lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, see step 4 on page 23.
PROBLEM: The displays of the console do not function properly
SOLUTION:
a. Remove the key from the console and
UNPLUG
THE POWER CORD.
Place the treadmill in the
storage position (see HOW TO FOLD THE
TREADMILL FOR STORAGE on page 25).
Remove the two #8 x 1 1/2" Screws (62).
Then, lower the treadmill (see HOW TO LOWER
THE TREADMILL FOR USE on page 25).
Tripped
Reset
c
62
62
a