NordicTrack 29836.1 Скачать руководство пользователя

Страница: 24 / 32

Locate the Reed Switch (95) and the Magnet (44)

on the left side of the Pulley (43). Turn the Pulley

until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet

and the Reed Switch is about 1/8 in. (3 mm). If

necessary, loosen the #8 x 3/4" Truss Head Screw

(19), move the Reed Switch slightly, and then re-

tighten the Screw. Reattach the Motor Hood (not

shown) with the five #8 x 3/4" Screws (not shown)

and run the treadmill for a few minutes to check for

a correct speed reading.

SYMPTOM: The incline of the treadmill does not

change correctly

a. With the key in the console, press one of the

Incline buttons. While the incline is changing,

remove the key. After a few seconds, reinsert

the key. The treadmill will automatically rise to the

maximum incline level and then return to the mini-

mum level. This will recalibrate the incline system.

SYMPTOM: The walking belt slows when walked on

Use only a single-outlet surge suppressor that

meets all of the specifications described on page

14.

b. If the walking belt is overtightened, treadmill per-

formance may decrease and the walking belt may

become damaged. Remove the key and UNPLUG

THE POWER CORD. Using the hex key, turn both

idler roller screws counterclockwise, 1/4 of a turn.

When the walking belt is properly tightened, you

should be able to lift each edge of the walking belt

2 to 3 in. (5 to 7 cm) off the walking platform. Be

careful to keep the walking belt centered. Then,

plug in the power cord, insert the key, and run the

treadmill for a few minutes. Repeat until the walk-

ing belt is properly tightened.

c. Your treadmill features a walking belt coated with

high-performance lubricant. IMPORTANT: Never

apply silicone spray or other substances to the

walking belt or the walking platform unless in-

structed to do so by an authorized service rep-

resentative. Such substances may deteriorate

the walking belt and cause excessive wear. If

you suspect that the walking belt needs more lubri-

cant, see the front cover of this manual.

d. If the walking belt still slows when walked on, see

the front cover of this manual.

Idler Roller Screws

2–3 in.

Front

View

1/8 in.

Содержание 29836.1

































Результаты поиска

Содержание 29836.1

Отзывы:

Похожие инструкции для 29836.1

Бренды по названию

Популярные бренды

NordicTrack 29836.1, Руководство пользователя

Результаты поиска

Содержание 29836.1

Отзывы:

Похожие инструкции для 29836.1

Бренды по названию

Популярные бренды