background image

29

GB

Fault finding

Fault

Possible cause

Remedy

Screen of keybord is 

not lit.

Power failure; the fuse is blown; 

the appliance is not plugged in 

correctly, the power is cut.

Check that power is connected. 

Reset the fuse

Temperature in 

freezer too high

The ventilation grille is blocked. 

The door is not closed properly. 

The quantity of items placed in 

the freezer at a time is greater 

than the capacity of the appli

-

ance. 

Thick layer of frost and ice. 

The temperature setting is too 

high

Ensure unhindered air circulation

Close the door and wait a few 

hours

Wait a few hours

Defrost the freezer.

Lower the temperature setting.

Temperature in 

freezer too low.

The temperature setting is too 

low

Raise the temperature setting

Vibration or bother-

some noise

The appliance is not level. 

Level the appliance (For model 

with adjustable feet: use a spirit 

level)

Compressor runs 

continuously.

The temperature setting is too 

low.

Too high room temperature.

Raise the temperature setting.

Ensure adequate ventilation

Display or alarm log 

shows ”RTC” error

The date and time is not set.

Please set the date and time 

Содержание ULT U100

































Отзывы: