background image

 

 
 
 

2

2

 

Technical Specifications 

      

      

      CAN ICES-3(A)/NMB-3(A) 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation. 

This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instruction manual, may cause harmful interference to 
radio communications. Operation of this equipment in a residential area is likely to cause 

harmful interference in which case the user will be required to correct the interference at their 
own expense. 

This Class A digital apparatus complies with Canadian ICES-003. 

Pursuant to EMC Directive – Article 9, this product is not intended for residential use. 

Table 1: System Specifications 

Supply Voltage (rated) 

12VDC 

Supply Current (rated) 

10A 

Hydraulic Pressure (maximum) 

3300 psi 

Baud Rate 

250 kbps 

Clock Frequency (maximum) 

96 MHz 

Solenoid Valve PWM Frequency 

300 Hz 

Ultrasonic Sensor Transmit Frequency  50 kHz 
Operating Temperature Range 

0°C to 80°C 

 

Содержание Active Roll Control UC5 JD 44952D
























Отзывы: