background image

 

 
 
 

11

5.3

 

Linear Roll Cylinder Assembly  

 

The linear roll cylinder must be mounted on the right hand side of sprayer. 

1.

 

In the linear roll cylinder crate is the linear roll cylinder, boom target, spring target and 
sensor bracket. 

 

Figure 10: Linear Roll Cylinder Assembly 

2.

 

Using the supplied 9/16 inch bolt, 5/8 inch lock washer and 9/16 inch washer, install the 
damper end (one port) of the linear roll cylinder onto the top mounting bracket.  (

Figure 

9

3.

 

Using the 1 inch bolt, 1 inch lock washer and 1 inch nut, attach the cylinder end of the 
linear roll cylinder to the bottom mount.  (

Figure 8

)  Be careful not to move the shaft of 

the cylinder because doing so will push oil out and suck air in. 

4.

 

Install the spring target and align by rotating the metal casing around the linear roll cylinder. 

5.

 

Install a sensor onto the sensor mounting bracket. 

6.

 

Mount the sensor bracket to the damper end (the end with no hoses).  A straight edge can 
be used to line up the spring target with the center of the hole on the sensor mounting 
bracket.  The mount should be facing as far forward as possible, but be sure it will not 
contact the catwalk when the boom is raised to the top. 

7.

 

Mount the cylinder target to the cylinder end (the end with hoses). 

8.

 

Align the cylinder target (bottom rod) so that it is 5/8” to the side of the spring target 
(

Figure 11

). 

 

Содержание Active Roll Control UC5 JD 44952D
























Отзывы: