Nomadic Display HangTen Скачать руководство пользователя страница 2

Страница: 2 / 12

Revised: 06/01/12

North America: 800.732.9395 Europe: +353.98.66011

Connect top H1/H2 extrusion to top V1 and
V2 extrusions (track on top). Lock with hex
wrench.

Lift frame by support extrusion and walk it
back into an upright position.

Connect bottom H1/H2 extrusion to
bottom V1 and V2 extrusions (track on
bottom). Lock with hex wrench.

Your Original frame is now ready for
graphics.

Slide monitor extrusion into place.

Lock with hex wrench at the top and
bottom.

Your Plus frame is now ready for
graphics.

Your Classic frame is now ready for
graphics.

Frame Setup Instructions

Place extrusions with locking hole facing
up and connect.

Monitor top to Monitor bottom
Top V1 to Bottom V1 / Top V2 to Bottom V2
Bottom H1 to Bottom H2 / Top H1 to Top H2*

Top H1 to Top H2*
If you have a header, slide H channel
above track. Lock tightly with hex wrench
provided.

Place foot upright on floor. Insert V1
extrusion into foot channel with locking
holes facing inward. Lock with hex
wrench. Repeat with V2 extrusion.

HangTen

Remove HangTen parts from black bag
and lay them out label side up. You will
build the frame on the ground facing
down.

Note: When tightening with hex wrench always give it a 3/4 turn clockwise until tight.

Frames • 2

Содержание HangTen












