24
1.6 Release the visor.
1.7 Remove the protective film from the Pinlock® inner visor and check that the entire
silicone-sealed profile of the inner visor adheres to the visor.
1.8 Fit the visor in the helmet.
CHECKING AND ADJUSTING THE INNER VISOR STRETCHING
Check the correct system assembly by opening and closing the visor. Check that both
visors are correctly fastened and do not move.
If the inner visor is not tightly fixed to the visor, move the external adjustment levers
simultaneously upwards to increase the stretch (Fig. 32). This operation must be carried
out gradually. The maximum stretch is achieved when the pin adjustment external levers
are turned outwards.
WARNING!
The presence of dust between the two visors may produce scratches on both surfaces.
Scratched visors and inner visors may cause reduced visibility and must therefore be
replaced.
Regularly check the correct stretching of the inner visor to prevent the same from moving
and scratching both surfaces.
If the helmet visor fogs up and/or condensation forms between the visors, check both for
system correct assembly and stretching.
An excessive and early stretch of the inner visor may result in excessive adherence
against visor surface and/or permanent deformations with subsequent inability to perform
following adjustments correctly.
The extended use under special weather conditions may reduce system performance and
result in partial fogging and problems of condensation on the inner visor. In
this case, remove the inner visor from the helmet visor and dry it with dry and lukewarm
air to restore system efficiency.
Intense sweating /breathing, the use under particular weather conditions (low
temperatures, and/or high humidity and/or sudden changes in temperature or heavy rain)
and intense and prolonged use may affect the performance of the system and cause the
fogging or formation of condensation on the inner visor.
In such cases, after using the helmet and to restore the system efficiency, remove the inner
visor from the helmet visor and let it dry with dry and lukewarm air. The same procedure
must be applied to the helmet, in order to dry out humidity in case it has formed up as a
consequence of the conditions described above.
2. PINLOCK® INNER VISOR DISASSEMBLY
2.1 Remove the visor equipped with Pinlock® inner visor.
2.2 Widen the visor and release the Pinlock® inner visor from the pins (Fig. 31).
2.3 Release the visor.
MAINTENANCE AND CLEANING
Remove the Pinlock® inner visor from the visor. Using a damp and soft cloth, gently clean
it with neutral liquid soap. Remove the soap under running water.
Dry the inner visor with dry and lukewarm air without wiping it.
Содержание N44
