12
2.2) VPS
assembly
2.2.1 Check that the control lever of the VPS is in the deactivated position (Fig. 4).
2.2.2 Insert the two pins of the VPS (B and C) in the holes on the terminal part of the lever (Fig. 6).
Note: To use the helmet with the visor and the VPS refer to the instructions contained in the paragraphs
from 1.2.1) to 1.2.5) of this instruction manual.
To use the helmet without reassembling the visor on the VPS continue reading the following instructions.
2.2.3 Check that the upper internal fastening of the latch (see “
Δ
” symbol) is lined up with the spline tooth
of the corresponding base (Fig. 2).
2.2.4 Insert the latch with its base into the mechanism paying attention to insert the upper (see “
Δ
”
symbol) and lower internal fastenings in the corresponding seats of the mechanism (Fig. 2).
Important: The left latch, identified with “L” on the inside, is different from the right one “R”.
2.2.5 Rotate the latch 90 degrees towards the rear part of the helmet.
2.2.6 Follow the same steps on the other side of the helmet.
2.2.7 Check that the latches are tightened properly and that the mechanisms work properly by pulling
the visor and / or the VPS up and down. If necessary, repeat the steps described above.
WARNING: Before using the helmet while riding always check and control that the mechanisms
work properly and have been assembled correctly by pulling the visor and/or the VPS up and down.
WARNING!!!
•
The VPS does not replace the protection guaranteed by the visor.
•
It is recommended not to use the helmet only with the visor assembled but without the VPS
because in this case the visor and the shell of the helmet will not adhere and seal up properly
together and this will cause air and / or water penetration.
•
Do not remove the visor/VPS opening and closing mechanisms from the shell.
•
After each assembly or disassembly procedure of the different parts, check that the visor mecha-
nism and the VPS mechanism work properly by pulling them up and down. If necessary, repeat the
steps described above.
•
If the opening and closing mechanisms of the visor and / or of the VPS are damaged or malfun-
ctioning, please contact a Nolan authorized dealer.
3)
REMOVABLE INNER COMFORT PADDING
3.1) Comfort padding disassembly
3.1.1 Open the chin strap (see specific instructions) and pull out the left fastening chin strap from the slot
on the cheek pad (Fig. 7). Repeat this step for the right fastening chin strap and cheek pad.
3.1.2 Open the rear zip, after releasing the puller from its holding elastic band “D” (Fig. 8), and the
back of the liner towards the inside of the helmet.
3.1.3. Release the left and right side flaps between the inner and outer shell (Fig. 9).
3.1.4. Hold the left front part of the liner and pull it upwards in order to remove the liner flap from the
support fixed to the polystyrene inner shell (Fig. 10). Repeat the same steps to remove the right
and central front flap.
3.1.5 Completely remove the liner from the helmet.
Содержание N33EVO
