10
INSTRUCTIONS FOR USE
Product configurations
The helmet N33 can be used with different Visor / VPS configurations as shown in Fig. 14.
Using the helmet in its full configuration (with visor pulled down) guarantees a higher level of
protection if compared with the other possible configurations.
1) VISOR
1.1) Visor
disassembly
1.1.1 Rotate the latch 90 degrees towards the rear part of the helmet (Fig. 1).
1.1.2 Remove the latch with its base from the mechanism (Fig. 2).
1.1.3 Remove the rear part of the visor from the mechanism and move it forward to release it from the
fastening A (Fig. 3).
1.1.4 Follow the same steps on the other side of the helmet.
Note: To use the helmet only with the VPS and without the visor, reassemble the latches and the bases
of the mechanism as described in paragraphs from 2.2.3) to 2.2.6) of this instruction manual.
WARNING!!!
•
The VPS MUST only be used according to the instructions provided in Chapter 2 (VPS
Operation and Precautions for Use) of this instruction manual.
•
The VPS does not replace the protection guaranteed by the visor.
1.2) Visor
Assembly
To assemble the visor check that the VPS is correctly placed on the mechanism. See paragraphs 2.2.1)
and 2.2.2) of this instruction manual.
1.2.1 Place the visor on the mechanism paying attention to insert it under the fastening A and push the
rear part to fasten it to the mechanism (see Fig. 3).
1.2.2 Check that the upper internal fastening of the latch (see “
Δ
” symbol) is lined up with the spline tooth
of the corresponding base (Fig. 2).
1.2.3 Insert the latch with its base into the mechanism paying attention to insert the upper (see “
Δ
”
symbol) and lower internal fastenings in the corresponding seats of the mechanism (Fig. 2).
Warning: The left latch, identified with “L” on the inside, is different from the right one “R”.
1.2.4 Rotate the latch 90 degrees towards the front part of the helmet.
1.2.5 Follow the same steps on the other side of the helmet.
1.2.6 Check that the latches are tightened properly and that the mechanisms work properly by pulling
the visor and / or the VPS up and down. If necessary, repeat the steps described above.
WARNING: Before using the helmet while riding always check and control that the mechanisms
work properly and have been assembled correctly by pulling the visor and/or the VPS up and down.
2)
VISION PROTECTION SYSTEM (VPS)
The new and exclusive Vision Protection System (VPS) is a
-moulded, antiscratch-treated
sunscreen. Using it is very simple and practical: Just pull it down or up to respectively activate it or
remove it from the field of vision. It is useful in all sorts of situations, both on long journeys out of town
and shorter town trips. Moreover, the innovative fastening system allows you to assemble and disassemble
the sunscreen without the need for any tools for ordinary maintenance and cleaning operations.
®
Содержание N33EVO
