background image

Sensitivity is the depth setting of the device. It is also 

used to eliminate the ambient electromagnetic signals 

from the surrounding environment and noise signals 

transmitted from ground.
Sensitivity consists of 30 levels and default setting is 25.
Sensitivity setting is a personal preference. However, It 

is important to set the sensitivity to the highest level 

possible where no major popping sounds are heard to 

avoid missing smaller and deeper targets. For example; if 

the noise level is suitable for searching and is the same 

at level 25 and 30, then 30 should be preferred.

Sensitivity is a common setting for all modes and 

changes to this setting will affect them all.

Adjusting the Sensitivity

On the main screen,  use the plus (+) and minus (-) buttons to 

increase or decrease the sensitivity. Single click to change the 

values one by one or hold down to change them rapidly.
The Sensitivity Indicator is located on the left side of the Target ID. 

The exact sensitivity level is shown numerically over the indicator. 

The indicator consists of 5 levels. Each level represents 6 units  of 

sensitivity. 
The sensitivity values corresponding to each level on the Depth 

Indicator are shown below:

The device always starts with the last adjusted sensitivity level.

IMPORTANT!

 To obtain maximum depth performance, to 

eliminate the noise caused by  electromagnetic interference, 

try shifting the frequency first.

25-30

19-24

13-18

7-12

1-6

SENSITIVITY

TARGET DEPTH

The device provides an estimated target depth according 

to the signal strength during detection. 

Depth Indicator: 

It shows the target's proximity to the 

surface in 5 levels during detection. As the target gets 

closer, the levels decrease and vice versa.

Depth detection is adjusted presuming that the target is a 2.5cm 

(1'') coin. Actual depth varies according to the size of the target. For 

instance, the detector will indicate more depth for a target smaller 

than a 2.5cm (1'') coin and less depth for a larger target.

IMPORTANT!

 As the operating frequency of the device has a 

direct impact on device, the estimated depth may vary for the 

same target during frequency changes.

Shallow target

Deep target

8

Park

Goldfield

Beach

Field

Содержание The LEGEND































Отзывы: