Nokia X7-00 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 48

background image

Nokia X7-00 / X7-00.1

RM-707 / RM-659

Service Manual Level 1&2

41

Confidential | Copyright © 2011 Nokia | All rights reserved

Version 1.0

43) Remove the DISPLAY protective film.

44) Remove the adhesive protective film from the
MENU / HOME KEY. Hold the MENU / HOME KEY as
shown with tweezers to avoid scratches. If possible
use plastic tweezers or tweezers with rubber tips.

45) Place the MENU / HOME KEY to the A-COVER TOUCH
ASSEMBLY as shown. Press the MENU / HOME KEY very
gently so that the adhesive does not activate
completely.

46) Check that the MENU / HOME KEY is aligned
correctly in to the A-COVER TOUCH ASSEMBLY. The
MENU / HOME KEY should be located on the center.
Press the MENU / HOME KEY for 3 seconds to activate
the adhesive.

47) Remove the inner A-COVER TOUCH ASSEMBLY
protective film.

48) Guide the TOUCH FLEX to its gap as shown. Be
careful not to damage the flex! Start placing the A-
COVER TOUCH ASSEMBLY to its place from the shown
side. Note that the A-COVER TOUCH ASSEMBLY has to
be assembled in a slight angle.

«
...
39
40
41
42
43
...
»

Содержание X7-00

















































Отзывы:

Нет отзывов

Похожие инструкции для X7-00

Бренд: Talkswitch Страницы: 29

Бренд: Talkswitch Страницы: 3

realpresence trio 8800

Бренд: Polycom Страницы: 7

Бренд: QUO Страницы: 5

Бренд: TCL Страницы: 61

Бренд: HIKVISION Страницы: 2

Бренд: Mircom Страницы: 39

Бренд: lepow Страницы: 2

Бренд: Avaya Страницы: 21

Бренд: Grandstream Networks Страницы: 62

Бренд: Alcatel Страницы: 51

StarLink SLE-LTEV-SS

Бренд: NAPCO Страницы: 2

Бренд: DDM Страницы: 24

Бренд: Samsung Страницы: 144

Бренд: Samsung Страницы: 160

Бренд: Samsung Страницы: 162

Бренд: Samsung Страницы: 186

Бренд: Samsung Страницы: 144

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды