Nokia X7-00 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 48

background image

Nokia X7-00 / X7-00.1

RM-707 / RM-659

Service Manual Level 1&2

35

Confidential | Copyright © 2011 Nokia | All rights reserved

Version 1.0

7) Push the EARPIECE with the SS-93 to its place as
shown. Be careful not to touch the highlighted area!

8) Remove the IHF SPEAKER MESH protective films.

9) Place the first IHF SPEAKER MESH with the
tweezers. Press it gently with the SS-93 to activate
the adhesive.

10) Then place the first IHF SPEAKER with the
tweezers. Note the alignment of the IHF SPEAKER.
Push the IHF SPEAKER with the SS-93 to its place as
shown. Be careful not to touch the highlighted area!

11) Use the same procedure as described earlier to
place the second IHF SPEAKER MESH and second the
IHF SPEAKER. Be careful not to touch the highlighted
area!

12) Peel off the DISPLAY CONDUCTIVE ADHESIVE
protective film.

«
...
33
34
35
36
37
...
»

Содержание X7-00

















































Отзывы:

Нет отзывов

Похожие инструкции для X7-00

Andi4 IPS Velvet

Бренд: iBall Страницы: 134

Бренд: Polycom Страницы: 36

Бренд: Bea-fon Страницы: 70

Orion Mini S350

Бренд: Posh Страницы: 20

A99-WMTA3030-01

Бренд: Westell Страницы: 12

Бренд: Plum Страницы: 19

Бренд: X-cam Страницы: 2

Бренд: Aquos Страницы: 186

Бренд: Docomo Страницы: 162

Бренд: NEC Страницы: 187

Бренд: Polycom Страницы: 12

Бренд: Philips Страницы: 2

Бренд: Samsung Страницы: 2

Galaxy GT-I7500

Бренд: Samsung Страницы: 87

Бренд: Samsung Страницы: 69

Galaxy GT-I5510

Бренд: Samsung Страницы: 115

Galaxy GT-i5500

Бренд: Samsung Страницы: 108

Galaxy GT-P7300B

Бренд: Samsung Страницы: 134

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды