Nokia NPD-1 Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 62

background image

CCS Technical Documentation

Troubleshooting — RF

NPD-1

Issue 1 11/2002



Nokia Corporation Confidential

Page 21

Troubleshooting: If –8 dBm cannot be attained, troubleshoot Cell TX as described in the
beginning of this chapter.

TN G_Offset Cell MD

See description of previous tuning. This step reports G_Offset.

The result is the value of G_Offset which gives –8.0 dBm transmitted power.

Manual Verification: See previous tuning. The value of G_Offset needs to be -8 dBm on
the center channel.

Troubleshooting: If G_Offset is not within the limits, troubleshoot the Cell TX as
described in the beginning of this chapter.

TN AMPS PL2 Po Mid (or Low, LowMid, MidLow, MidHigh, HighMid, or High)

This procedure tunes the AMPS transmit Power Level 0 on seven channels by adjusting
TxdBCtr. The channels are: Low= 991, LowMid= 107, MidLow= 245, Mid= 384,
MidHigh= 521, HighMid= 660, High=799. The algorithm then interpolates between the
measured points for frequency compensation.

The result is measured transmit power in dBm for power level 0 on each of the seven
channels.

Manual Verification: Set the phone to local mode and turn on the AMPS transmitter to
the channel which failed.

Using the Phoenix “RF Tuning” window, set “mode” = RF Tuning, and select this test.
Adjust TxdBCtr in the “values” dialog box until the output power is within the limits
(adjusting for cable loss).

Troubleshooting: Troubleshoot the cell transmitter as described in the Probing/Trouble-
shooting Tables and Diagrams section, setting the TX AGC values to those listed for

Channel

Cell

PCS

Low

991

25

LowMid

107

200

MidLow

245

400

Mid

384

600

MidHigh

512

800

HighMid

660

1000

High

799

1199 (1199 not a voice channel,
but used in tuning

«
...
19
20
21
22
23
...
»

Содержание NPD-1 Series































































Отзывы:

Нет отзывов

Похожие инструкции для NPD-1 Series

Бренд: D-Link Страницы: 56

Бренд: Panasonic Страницы: 100

Бренд: Panasonic Страницы: 5

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 12

Бренд: Damall Страницы: 7

SGH T729 SGH-Blast Series

Бренд: Samsung Страницы: 163

Бренд: NTT docomo Страницы: 68

Бренд: Fysic Страницы: 60

Бренд: Mobeye Страницы: 28

Бренд: Pacific GSM Страницы: 8

Бренд: Nortel Страницы: 112

Бренд: TAG Heuer Страницы: 62

Бренд: SoftBank Страницы: 2

Бренд: Talkaphone Страницы: 8

Бренд: Samsung Страницы: 340

Бренд: Samsung Страницы: 218

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды