background image

6

4. AIR SUPPLY

CAUTION

 Draw off drainage before starting operation.  If 

the drainage enters into the tool, it can freeze 
around the exhaust port of the tool and result in 
output power reduction.

4-1. Air Pressure

Adjust air pressure to 0.6MPa (or 6 kgf/cm

2

) with 

the air regulator. Lower pressure may result in 
insuf

fi

cient performance. Higher pressure may result 

in premature wornout of parts. It is important to 
maintain the proper pressure with pressure regulator 
on air line.

4-2. Air Line 

(Fig.2)

Use a 9.5mm (3/8”) I.D. [MLG-25] or 12.7 mm (1/2”) 
I.D. [MLG-40, MLG-50, MLG-70] air hose between 
the compressor and the tool. Compressed air comes 
to be cooled down and its drain be separated, as 
soon as the air leaves the compressor. The drain, 
however , is condensed in the piping, and can 
enter into the tool mechanism, and may cause 
malfunction. So, install an air filter and an oiler 
between the compressor and the tool.

4-3. oiler

Install an oiler between the compressor and the tool.  
Use machine oil ISO VG-10 for lubrication and rust 
prevention. Negligence of the oil supply may cause 
damages on the tool. Lubricating the tool with high 
viscosity oil reduces the tool performance.

4-4. Lubrication 

(Fig.2)

Before starting the tool, disconnect air hose from 
the tool and supply a few drops of machine oil ISO 
VG-10 to the air inlet port of the tool. Then reconnect 
and make idle running for a few seconds so that the 
oil should reach every part in the tool. 

Air Regulator

Oiler

Air Filter

Compressor

Lubrication

Tool

9.5mm (3/8”) I.D. Hose [MLG-25]
or 12.7mm (1/2”) I.D. Hose
[MLG-40, MLG-50, MLG-70]

Cupla

Fig. 2

5. PREPARATION (MLG-50, MLG-70)

Mounting the Handle Ass’y 

Screw the Handle Ass’y into the Housing Sub Ass’
y. It can be mounted on either right or left side of the 
Housing Sub Ass’y. Be sure to mount the Handle Ass’
y before use.

+DQGOH$VVҋ\

Fig. 3

6. GRINDING WHEELS

WARNING

The maximum operating speed marked on the Grinding 
Wheel, blotters, or packaging, shall equal or exceed 
the rated speed on the grinder.
Use with Type 27 Depressed Center Grinding Wheels.

MLG-25

A

M6

B

C

Fig. 4

MLG-40

0

$

%

&

Fig. 5

Содержание MYTON MLG-25

















Отзывы: