NimbeLink Skywire NL-SWN-LTE-NRF9160 Скачать руководство пользователя страница 3

Страница: 3 / 22

1. Introduction

1.1 Scope

This document serves as the user manual for the Skywire Nano Development Kit.

1.2 Orderable Devices

Orderable Device

Description

Carrier

NL-SWNDK

Skywire Nano Development Kit

Any

NL-SWN-LTE-NRF9160

Skywire Nano, Global, CAT M1, NBIoT, GPS

Any

1.3 Product Overview

The NL-SWNDK is a development kit made for use specifically with the Skywire Nano

embedded cellular modem that enables easy development and integration of the

Skywire® Nano into a custom design.

The NL-SWNDK offers the following critical features and functionality:

●

One micro-USB connector, J2, that provides 5V, 500mA power to the board, and

enables easy communication between the host PC and the modem.

●

Two SMA to U.FL connectors for cellular and GPS antennas

●

Two 20-pin headers for connection to modem's GPIO pins, and other signals.

●

3FF SIM slot that adds support for various other SIM cards and cellular carriers.

For more information regarding the development kit, please refer to the NL-SWNDK

datasheet and design files:

Datasheet: Coming Soon

Design Files:

https://nimbelink.com/Documentation/Development_Kits/NL-SWNDK/1002333_REVB_
NL-SWNDK_Design_Files.zip

PN 1002398 rev 1

Содержание Skywire NL-SWN-LTE-NRF9160






















Результаты поиска

Содержание Skywire NL-SWN-LTE-NRF9160

Отзывы:

Бренды по названию

Популярные бренды

NimbeLink Skywire NL-SWN-LTE-NRF9160, Руководство пользователя

Результаты поиска

Содержание Skywire NL-SWN-LTE-NRF9160

Отзывы:

Бренды по названию

Популярные бренды