NimbeLink Skywire NL-SWN-LTE-NRF9160 Скачать руководство пользователя страница 22

Страница: 22 / 22

5. Appendix

5.1 APN Configuration

5.1.1

Overview

APNs are used by devices and cellular networks to initialize and properly set up a

cellular connection. In order to connect to a cellular network, it is crucial to ensure that

the proper APN is set on the device.

If the Skywire Nano was activated on

https://go.nimbelink.com

, use the proper APN

from the table below. For data plans not activated through NimbeLink please reach out
to your carrier for correct APN configuration details.

5.1.2

Common APN's and Their Respective Carriers

The table below contains a list of common APNs and their respective carriers.

It is important to use the APN that corresponds to the proper carrier and the specific IP

address configuration. Failure to do so will result in failed cellular network connections.

Cellular Carrier

Common APNs

Description

Verizon

NIMBLINK.GW12.VZWENTP

APN for Verizon devices activated
through

go.nimbeLink.com

MW01.VZWINTERNET

APN for devices upgraded to a Public
Static IP address

AT&T

iot0718.com.attz

AT&T Direct APN

PN 1002398 rev 1

Содержание Skywire NL-SWN-LTE-NRF9160






















Результаты поиска

Содержание Skywire NL-SWN-LTE-NRF9160

Отзывы:

Бренды по названию

Популярные бренды

NimbeLink Skywire NL-SWN-LTE-NRF9160, Руководство пользователя

Результаты поиска

Содержание Skywire NL-SWN-LTE-NRF9160

Отзывы:

Бренды по названию

Популярные бренды