Nilfisk-Advance RS 850, Руководство пользователя

Страница: 150 / 208

ENGLISH
USER MANUAL
36 33014576(4)2008-02 A RS 850
SIDE BROOM POSITION CHECK AND ADJUSTMENT
NOTE
Brooms of various hardness are available. This procedure is applicable to all types of brooms.
Check
Check the side brooms for proper height and tilting, according to the following procedure:
Drive the machine on a level ground.
While keeping the machine stationary, fully lower the side brooms and allow them to rotate for a few seconds.
Stop and lift the side brooms, then move the machine.
Check that the size and orientation of the prints left by the side brooms are as follows:
The right side broom must touch the ground along a circle arc ranging from “11 o’clock” position to “4 o’clock” position
(1, Fig. AE).
The left side broom must touch the ground along a circle arc ranging from “8 o’clock” position to “1 o’clock” position (2,
Fig. AE).
Adjust the broom height when the prints are out of specifi cation, according to the following procedure.
Engage the parking brake with the lever (13, Fig. E).
Turn the ignition key (24, Fig. D) to OFF position and remove it.
Side broom height adjustment
On both sides of the machine, operate on the tensioning self-locking nut (3, Fig. AF) of the spring (4) and consider the
following:
To lower the broom, the nut (3) must be unscrewed;
To lift the broom, the nut (3) must be screwed.
Perform step 1 again.
Side broom forward tilting angle (5, Fig. AF) adjustment
On both sides of the machine, loosen the locknuts (6 and 7, Fig. AF), then adjust the forward tilting angle (5) by placing a lever
in the hole (9) and turning the tie rod (8).
When the adjustment is completed, tighten the locknuts (6) and (7).
Perform step 1 again.
Side broom side tilting angle (10, Fig. AF) adjustment
On both sides of the machine, loosen the screws (11 and 12, Fig. AF), then adjust the side tilting angle (10). When the
adjustment is completed, tighten the screws (11) and (12).
Perform step 1 again.
Side broom side position adjustment
The purpose of this adjustment is to improve the side position of the brooms as to the suction inlet (17, Fig. G).
To perform the adjustment, loosen/tighten the self-locking nuts (1 and/or 2, Fig. AG), thus changing the side position of the
brooms. To have a optimum adjustment, the arms must be slightly tensioned outwards.
When the side brooms are too worn out, the adjustment is not possible; replace the brooms according to the instructions in the
relevant paragraph.
3RD BROOM POSITION CHECK AND ADJUSTMENT
NOTE
Brooms of various hardness are available. This procedure is applicable to all types of brooms.
3rd broom position check
Check the 3rd broom for proper height and tilting, according to the following procedure:
Drive the machine on a level ground.
Start the machine and bring the 3rd broom arm (1, Fig. AH) straight in front of the cab (as shown in the fi gure) according to
the procedure shown in the relevant paragraph.
Keeping the machine stationary, lower the 3rd broom completely (2, Fig. AH) and allow it to rotate for a few seconds.
Stop and lift the 3rd broom, then move the machine.
Check that the size and orientation of the print left by the 3rd broom is as follows:
The broom must touch the ground along a circle arc ranging from “10 o’clock” position to “2 o’clock” position (3, Fig.
AH).
The broom forward tilting angle (4, Fig. AH) must be 10 degrees approximately.
If necessary, adjust the broom according to the following procedure.
Engage the parking brake (13, Fig. E).
Turn the ignition key (24, Fig. D) to OFF position and remove it.
1.
•
•
•
•
–
–
•
2.
3.
4.
•
•
5.
6.
7.
8.
9.
10.
11.
12.
13.
1.
•
•
•
•
•
–
–
2.
3.